Installation Guide

ManualsBrandsSALUS ManualsWiredSALUS Programmable Wired Thermostat VS30W/VS30B

Table Of Contents

Temperature setting

Programming

Manual mode - temperature settings

NSB function - automatic mode

Installer settings

Error codes

dxx Function Value Description

Default

value

d01

Control method

temperature

0 PWM algorithm

1 Span ±0.25°C

2 Span ±0.5°C

d02 Oset temperature

from -3.0°C

to +3.0°C

If the thermostat indicates

wrong temperature, you

can correct it by ± 3.0°C

0°C

d03

Using a oor tempera-

ture sensor (S1, S2)

0 No sensor

1 Sensor is connected

d04

External sensor

used for air

or oor temperature

measurement

(Function is active,

when d03=1)

Thermostat measures the

temperature only on the

external sensor

The sensor is used

as a protection against

overheating the oor

d05

Cooling mode control

method

1 Span ±0.5°C

2 Span ±1.0°C

d06

Type of thermoelectric

actuator

0 NO - normally open

1 NC - normally closed

d07 Valve protection

0 OFF

1 ON

d08

Frost protection

temperature

5-17°C

Frost protection / Holiday

mode temperature

5°C

d09 Clock format

0 12 hour

1 24 hour

d11 Daylight Saving Time

0 OFF

1 ON

d12

Heating temperature

limit

5-35°C

The maximum heating

temperature that can be set

by the user

35°C

d13

Cooling temperature

limit

5-40°C

The minimum cooling

temperature that can

be set by the user

5°C

d14

Maximum oor

temperature

(this function is active

in heating mode when

d04 = 1)

6-45°C

In order to protect the oor

from overheating, heating

will be turned OFF, when the

maximum temp. of the oor

sensor will be reached

27°C

d15

Minimum oor

temperature

(this function is active

in heating mode when

d04 = 1)

6-45°C

In order to protect

the oor, heating will

be turned ON, when the

minimum temp. of the oor

sensor will be reached

10°C

d16

Lower oor temperature

limit for cooling

(this function is active

when d04 = 1)

6-45°C

In order to protect the oor,

cooling will

be turned OFF, when

the minimum temp. will

be reached

6°C

d17

Choice of the default

program

1-5

Selection 1 of the 5 default

programs

d18

Operating mode

HEATING / COOLING

0 Heating system

1 Cooling system

Error code Description

Err02 The maximum / minimum oor temperature has been exceeded

Err03 Temperature sensor is faulty

Err04 Temperature sensor is shorted

3 sek.

Set the temperature

with or buttons.

Select the service parameter

using or buttons.

The parameter value

is set by or .

Press to conrm the changes.

ress to conrm the changes.

Press to conrm the changes.

Current temperature.

Temperature set in the selected

operating mode

Select the automatic mode

using or buttons.

Press any button to highlight the screen, then follow the steps below:

Thermostat also has 2 additional modes:

The NSB (Night SetBack) function can automatically change temperatures

on VS35 daily thermostats via VS30 programmable thermostat connected to

a wiring centre (or another external clock). NSB function switches between

comfortable temperature and economic temperature .

To activate the automatic mode, select the icon. On display together with

the icon, the controller indicates active temperature mode: or .

- Comfort mode

- Standard mode

- Economic mode (when this mode is selected on the NSB output

appears 230 V AC voltage)

- PARTY mode sets the comfort temperature for a dened time

by the user (maximum 9 hours 50 minutes).

- The HOLIDAY mode sets the frost protection temperature for a user

dened period of time (maximum 99 days).

- Frost protection mode. Usually used in a longer period of absence

or during the holidays (available only in heating mode).

Press any button to highlight the screen, then follow the steps below:

Note: For the NSB function to work, it is necessary to connect the wirings

properly. Connection diagrams can be found on the previous page.

Note: To restore the thermostat’s factory settings, in step 2 set the PSuu

to 47 code, and conrm the selection with the button.

3 sek.

Press any button to highlight the screen, then follow the steps below:

Use button to choose days

range for schedule:

Select the operating mode.

Set the program start time:

Repeat steps 5 - 10 to set time

and temperatures for next time

ranges. No hour (--:--) on the

display means whole day

is planned already.

Schedule can be divided into

maximum 6 time r

anges.

- whole week

- weekdays

- weekends

- each day separately

There are 4 temperature levels available. In manual mode only one temperature

level is active (icon in the frame indicates which mode is currently chosen).

For each temperature levels you can set a dierent temperature.

Press any button to highlight the screen, then follow the steps below:

Choose the temperature mode

using or buttons.