Pedi Whirlpool Pedicure Spa Manual
Thank you for choosing , the leading manufacturer well known worldwide for its innovation and design in pedicure spas. takes pride in bringing you quality products that meet today’s demand for safety and service. The Pedi Whirlpool Pedicure Spa has been designed for dependability, and to benefit all with a health conscious clientele. PLEASE TAKE TIME TO READ THIS MANUAL THOROUGHLY BEFORE USE.
Pedi Whirlpool Pedicure Spa IMPORTANT INFORMATION Serial Number: Order Number: Installed by: Installation date: Chair Serial Number Salontech LLC 57 Seaview Blvd. Port Washington, NY 11050 Tel: 516-484-4937 ”35Fax: 516-484-4938 www.salontech.com info@salontech.
Important Considerations Electrical Service A 110V, 60 Hz, 15 Amp GFCI protected grounded circuit must be used to supply power to each individual pedicure spa. Water Supply All plumbing connections must conform to local codes. Water supply to the spa should be provided with adequate water pressure and water temperature. Water pressure To fill the basin correctly up to level, Normal water pressure of 30 to 80 P.S.I is required. Water temperature The hot water supply temperature must not exceed 140 .
Caution Please DO NOT lift or move the Spa with faucet handle Warranty will be null and void.
Pedi Identifying components 14 1 16 2 stop position 3 power 5 partial 13 full percussion upper compression lower kneading rolling 12 6 7 ON OFF 11 5 10 15 2 3 6 17 4 9 8 Components 1 - AUTO SLIDER REMOTE CONTROL (AUTOMATIC SLIDER) 11 - MASSAGE MAIN ON/OFF SWITCH 2 - CLEAN PIPELESS JET / CLEAN JET COVER 12 - MASSAGE AND BUILT IN RECLINER REMOTE CONTROL 3 - SHOWER SPRAYER 13 - BACKREST 4- SHOWER STAND 14 - HEAD PILLOW 5 - DRAIN PLUG 15 - FUSE FOR MASSAGE SYSTEM 6 - OVERHEAD W
Pedi Specification ( PipeLess Clean Jet System) Dual Clean Pipeless System with Adjustable air control system for powerful whirlpool action P-tr ap and 1 -1/2” exten sion PVC pipe Specification ( PipeLess Clean Jet System) Dimension & Weight Pedi-Joy (Base unit) Pedi-Joy (Chair) Stool 58”L x 32”W x 21”H Shipping Wt.130 Lbs 52”L x 32”W x 21”H Shipping Wt. 115 Lbs. 20”L x 12”W x 17”H Shipping Wt. 18 Lbs Capacity of Tub 4.
Pedi 26” 27” 29” 54” 42” Plumbing connection area Drain Pipe extension Center of drain to end of drain pipe 38” 2” 2-3/4” 3” 10” Plumbing Fitting Required space for installation 15” Wall Salontech,LLC Top / Rear view Pedi-Joy Salontech,LLC
Installation Specifications Summary Warning: Failure to comply with federal, state or local codes and ordinances will result in warranty being null and void. As stated, the pedicure spa installation must comply with all plumbing and electrical codes. A licensed plumber and licensed electrician must complete the applicable connections of the pedicure spa. Location and support Select a level location. The floor structure beneath the pedicure spa must be capable of supporting the occupied pedicure spa.
2-3/4” Pedi 21” 2-3/4” 37-1/2” 1” Extension Pipe ½”Discharge outlet 3/4” inlet 37-1/2” 41-1/2” 15” ½”Hot&Cold water inlet 46-1/2” 15” ½”Hot&Cold water inlet 46-1/2” 21” 2-3/4” Pedi Wall Drain 37-1/2” 41-1/2” 15” ½”Hot&Cold water inlet 46-1/2” Note: The requirement for the vacuum breaker varies from state to state and province to province, Please consult with the licensed plumber.
Pedi Back Flow Preventive Device The back flow preventive device will not be mandated for us to install, But it is an optional item. If your state requires back flow preventive device on the pedicure unit, you MUST specify in your order. We recommended to pre-install by MFG. The specification, back flow preventive device description, requirement and certificate numbers are as indicated below.
Massage System Important Safety Instructions Warning: To reduce risk of burns, fire, electric shock or injury; Read all instructions before using; burns will result from improper use, never remove cover other than authorized from the manufacturer. Close supervision is necessary when unit is used by, on, or near children, and disabled people. Use this unit only for its intended use as described in this manual. Do not use any attachment/s not recommended by the MFG.
Chair assembly Tool Required 13 mm rachet Vise Grip plier Bottom view (Chair) Align rear of the hole onto the swivel and tighten one at a time. R E A R Swivel Pre-install swivel to the base. Base (Body) R E A R Base with spacer for reinforcement and support swivel as well as chair.
Maintenance Suction It is important to keep the suction screen from any blockage or obstructions at all times, due to they may reduce the whirlpool action and may cause damage to the pump. To Clean: Take off suction screen by removing two screws and clean with soft brush while immersed in disinfectant. After each customer (Standard Jet System Users) 1. 2. 3. 4. Drain completely and remove residual debris from basin. Clean the surfaces and basin with mild detergent, rinse with fresh water.
Pedi Clean Jet System - Clean Jet System users Maintenance Keep the screen of the jet inlet free of debris. Any blockage of the screen reduces the whirlpool action and may cause damage to the jet motor. Disassemble en Op 1 Cl ose To Open 1. 2. 3. 4. 5. 6. Hold the Jet cover as shown left. Gently rotate to left to open. Pull gently outward. Clean jet component, Remove all debris from jet cover and locking mechanism. Clean all debris inner side of the jet as shown below left.
Chair Maintenance Outside Cover Open zipper to either side Inner cover lining for easy access to the mechanism. Under the head rest, you will find zippers to open outside cover. As shown Removable Padding location For high density of massage, remove extra padding. As shown Mechanism Cover Zipper Location Note: Always clear passage of the up/down movement. 1- As shown, Lubrication is MUST be applied quarterly. 2- Check loose wire on limited switch. 3- Do not lubricated excessively.
Cautions To Reduce the potential risk of fire, electrical shock or injury : 1. 2. 3. 4. 5. All electrical wiring (both installation and repair) must be done by a licensed electrician and in accordance with local and state ordinances. No modifications, addition or deletions should be made to the pump without MFG approval. Before starting motor, fill the tub with water to the level recommended by MFG. Never run dry.
Pedi Discharge Pump Two Minute Timer Fastner Power Cord On/Off Switch Air Tubing Figure 2 Outlet Pluggs Tip of the clear hose MUST be above the water level. ½”Check Valve (Provided by MFG) Loop to connect Main Drain 1/8” clear tubing Discharge Pump Drain Elbow 1” PVC Pipe 1-1/4" E-Z Connector 3/4”x1” adapter 1-1/4” Drain Elbow Installation Instruction 1. Make a hole ( size 1-3/8”) for the On/Off switch as shown (see fig 1). Pre-drill required. 2.
Warranty Form Customer MUST fill in blank and return to us with sale receipt in order to obtain warranty service. The sales receipt MUST indicate the purchase date and distributor. Return Address: Salontech LLC 57 Seaview Blvd. Port Washington NY 11050 T: 516.484.4937 F: 516.484.4938 E-mail: info@salontech.com Web : www.salontech.
SALONTECH LIMITED WARRANTY Manufactures the PediJoy, Whirlpool Pedicure Spa with the highest standards for quality materials , which UL listed components and highest workmanship for duration of the warranty period, which duration begins on the date of purchase by the customer (end-user). Each customer is responsible for maintaining, proof of purchase (invoice) and to initiate the warranty. The customer MUST send in warranty card in the manual booklet.
