Installation Guide
Sakrete® 5000 Plus Concrete Mix is a professional high early strength
blend of portland cement, sand and gravel that is formulated to attain
high early strengths and superior durability. For repair and building jobs
where concrete thickness exceeds 2 inches (50 mm). Ideal for building
walks, drives, patios and steps, as well as pouring footings and setting
posts and poles. Just add water and mix.
FOR COUNTERTOP APPLICATIONS ONLY the concrete can be applied
to a minimum thickness of 1 1/2”. Endorsed by CHENG Concrete, the
leading innovator in the design and creation of concrete countertops by
Fu-Tung Cheng.
SAFETY:
READ and UNDERSTAND the Material Safety Data Sheet (MSDS) before using
this product. WARNING: Wear protective clothing and equipment. See HMIS
block. For emergency information, call CHEMTREC at 800-424-9300
or 703-527-3887 (outside USA). KEEP OUT OF REACH OF CHILDREN.
PREPARATION:
When repairing concrete, remove all loose and foreign material. Dampen
adjoining concrete surfaces.
MIXING:
Empty the contents into a mortar box, wheelbarrow or mechanical
mixer. When mixing by hand, form a crater for adding water. Add
approximately 4 quarts (3.7 L) of clean water per 80 lb. (36.2 kg) bag or
enough to achieve a workable mix. If too stiff, add more water a little at a
time. Avoid a soupy mix. Excess water reduces strength and durability and
can cause cracking. In cold weather use warm water to accelerate the set.
Use cold water to slow the set in hot weather.
PLACEMENT:
Place and consolidate the SAKRETE® 5000 Plus Concrete Mix.
Work the material into voids, then level the surface with a straight edge
board. Allow freshly placed concrete to set about 1 hour or until the surface
water has begun to disappear before fi nishing. Time will vary with weather
conditions.
FINISHING:
Level with a screed and allow the bleed water to evaporate. Use
a fl oat to remove surface imperfections and trowel to a smooth fi nish. For a
rougher surface, use a broom. Refer to ACI 302. Finishing cementitious mate-
rials too early, or over-working the materials can cause dusting, cracking,
scaling and a weak surface.
CURING:
Curing means maintaining proper moisture and temperature. Account for local
environmental conditions when selecting the curing method. High heat, low
humidity or wind will increase the evaporation of water. Keep the surface
damp using a sprinkler, wet burlap, Sakrete Cure ‘N Seal or cover with plastic
for several days as needed. In cold weather adequately cover and keep from
freezing for a minimum of 24 hours. Refer to ACI 308.
When used as directed and in accordance with ASTM C 387 Specifi cation,
SAKRETE® 5000 Plus Concrete Mix exceeds 5,000 psi after 28 days.
STORAGE:
Store in a tightly closed container off the fl oor in a dry place.
TECHNICAL DATA:
Exceeds ASTM C 387 when used as directed
Compressive Strength
3 day 2,500 psi (17 MPa)
7 day 3,500 psi (24 MPa)
28 day 5,000 psi (34 MPa)
To determine coverage: Multiply Length x Width x Thickness all in feet
(meters) = cubic feet (cubic meters): divide by 0.60 cubic feet (0.016 cubic
meters) per bag = Number of 80 lb. (36.2 kg) bags needed for given job.
NOTE: Convert all measurements in inches (mm) to feet (meters). 4 inches
(100 mm) = 0.33 feet (0.1 m)
PACKAGING:
80 lb. bag (36.2 kg) - UPC: 7-64661-10380-6
5000 Plus High Strength
Concrete Mix
www.sakrete.com • 866-SAKRETE 866-725-7383
REV 3-10
How Much Concrete Do You Need?
Estimate of the number of whole 80lb. (36.2 kg) bags of
Sakrete 5000 Plus Concrete Mix to place a slab
Area in Sq. Ft. (sq. m.) 3 (.03) 6 (.06) 9 (.08) 15 (1.4) 24 (2.2) 45 (4.2)
Slab 4” thick (100 mm) 2 4 5 9 14 25 Bags
Slab 6” thick (150 mm) 3 5 7 13 20 38 Bags