Datasheet

22
±1
2
13
L
±1
19
±1
7.9
1 1.6
1.6
d
2
D
1.5
d1
0 -0.05
10.32
0 -0.05
7.6
±0.2
R16.5MAX
1.2
A
b
t.3
0°
37
Model 22HP-10
●
Standard Dimensions
●
Standard Model Nos.
5-turn models:
22HP-5 22HP-5M
22HP-5E 22HP-5N
10-turn models:
22HP-10 22HP-10M
22HP-10E 22HP-10N
●
General Specifications
Standard Resistance
Range:
Total Resistance
Tolerance:
Independent Linearity
Tolerance:
Power Rating:
Noise:
Electrical Travel:
Mechanical Travel:
InsulationResistance:
Dielectric Strength:
Starting Torque:
Stopper Strength:
100Ω to 50kΩ (5-turn)
100Ω to 100kΩ (10-turn)
Standard Class
±5% (J)
Precision Class
±1% (F)
5-turn 10-turn
Standard Class
±0.3% ±0.25%
Precision Class
±0.2% ±0.1%
(Below 5kΩ)
1.0W (5-turn)
2.0W (10-turn)
Below 100Ω E.N.R.
360°
×n ±5°(n: No. of turns)
360°
×n (n: No. of turns)
Over 1,000MΩ at 500V.D.C.
1 minute at 1,000V.A.C.
Below 10mN
•
m (100gf
•
cm)
Approx. 0.35N
•
m (3.5kgf
•
cm)
Max. Torque exerted
on fastening the
mounting nut to the
bushing:
Max. Working Voltage:
Resist. Temperature
Coefficient of Wire:
Materials:
Mass:
Below 1.0N
•
m (10kgf
•
cm)
(In case of panel thickness with
over 2.5mm., the rotating torque
may become heavier.)
250V
±20p.p.m./
Shaft: Stainless steel
Housing case : Glass-filled nylon
Bushing: Glass-filled nylon
(For ganged version,
the bushing is metal-
brass without plating.)
Terminals: Gold-plated brass
(All terminals can be
fitted with the AMP
110 series faston
receptacle
(2.8
× 0.5mm)
or equivalents.)
Approx. 20g (Both 5-turn and 10-turn)
●
Special Specifications Available
Shaft with front and rear extension (Rear shaft with 6mm dia. and 15mm length), Multi-ganged (Available up to 10
gangs), With high torque, Special shaft dia. (∅3mm, ∅3.175mm, ∅4mm, ∅5mm), Special machining on the shaft,
With plastic shaft, Metal bushing type (22HPM-n with anti-rotation pin), 1, 2, 3, 4, 6, 7 and 8-turn versions are
available (These versions have same outer dimensions, but general specifications are please request us for details),
Simple sealed housing, Slipping-clutch incorporated type, Extra taps (Available up to 1 tap only for 10-turn model),
Servomount type (Same dimensions as 22HHPS-10).
+10°
0°
Wirewound
MODEL 22HP
(Bushingmount)
LOW-COST ITEM
U.S.A. PAT. No.4400687 F.R.G. PAT. No.3136765 HONGKONG PAT. No.751 of 1984
U.K. PAT. No.2087160 FRANCE PAT. No.8118538 SINGAPORE PAT. No.372/84
Note: 1. 1 pc. each inner teeth washer and hex nut are attached.
2. Outer dimensions of 5-turn version are same as those of 10-turn.
3. Housing length of 2 ganged version is extended by 19mm.
4. Please process the mounting hole on the panel to be mounted with
this potentiometer by the diameter of 10.32mm .
Note: Please select the exact model number
from the right-side table, because
each model number has different
shaft dia. and bushing dimensions.
Model No.
22HP-10
Shaft
Dimensions
Mounting Screw
d2 D
Anti-rotation
d1 L
∅6
3/8-32UNEF20.6 Yes
No
Yes
No
22HP-10M
∅6
M9 P=0.7525.0
22HP-10E
∅6.35
3/8-32UNEF20.6
22HP-10N
∅6
M9 P=0.7520.6
●
Standard Resistance Values ■No. of Wire Turns ■Resistance Wire Used
Resist. Value (Ω) 100
1,240
2,100
200
1,560
2,480
500
2,000
3,300
1k
2,510
4,000
2k
2,400
5,020
5k
3,200
5,000
10k
3,900
6,400
20k
4,800
7,800
50k
5,500
10,100
100k
11,000
22HP-5
22HP-10
Resist. Wire Used Cu-Ni System Ni-Cr System
+
0.05
0
(±0.25%) (±0.15%)