Datasheet
44
(with inch dimensions)
●
General Specifications
Standard Resistance
Values:
Max. Practical
Resistance Value:
Total Resistance
Tolerance:
Independent Linearity
Tolerance:
Resolution:
Output Smoothness:
Contact Resistance
Variation:
Power Rating:
Electrical Travel:
Mechanical Travel:
1k, 2k, 5k, 10k, 20k, 50k (Ω)
100kΩ
Standard Class
±10% (K)
Precision Class
±5% (J)
Standard Class
±0.4%
Precision Class
±0.1%
(
±0.2% in case of below 5kΩ)
Essentially infinite
Below 0.05% against input voltage
Below 5% C.R.V.
1.0W
3,600°
±5°
3,600°
Insulation Resistance:
Dielectric Strength:
Starting Torque:
Stopper Strength:
Max. Torque exerted
on fastening the
mounting nut to the
bushing:
Max. Working Voltage:
Resistance
Temperature
Coefficient:
Mass:
Over 1,000MΩ at 500V.D.C.
1 minute at 1,000V.A.C.
Below 3mN
•
m (30gf
•
cm)
(Bushingmount type)
Below 2mN
•
m (20gf
•
cm)
(Servomount type)
Approx. 0.15N
•
m (1.5kgf
•
cm)
Below 0.8mN
•
m (8kgf
•
cm)
450V
±100p.p.m./
Approx. 10g
●
Special Specifications Available
5-turn type (S12HHP-5E), Shaft with front and rear extension (Rear shaft with 0.8mm dia. and 10mm length), Special
machining on the shaft, Simple sealed housing (in case of servomount type, the housing length becomes longer by
1.5mm.).
+15°
0°
The World's Newest Snapping-in Construction in Model 22HP series
(PAT.)
By using most modern plastic engineering technology as well as our patented designs, number of parts can be
reduced steeply by about 50% almost without any degradation in all performances and by that means, the total cost-
down by 30 to 50% is achieved in comparison with similar multi-turn potentiometers of the same diameter.
MODEL 12HHP-10E
Bushingmount
Servomount
()
13
±0.5
4
±0.5
7.5
±0.5
14
±1
23 1
1
/
4 -32UEF-2A
25.5
±1
1.5
±0.2
20
±1
7
±0.5
7.14
0
-0.05
5
±0.5
7.8
±0.5
10
±0.5
10
±0.5
5
±0.5
13
2
5 1.2 holes
510
5
10
28.2
±1
1.57
±0.2
1.57
4
±1
7.5
±0.5
14
±1
11.5
±0.5
9.5
MAX
12.7
+0.13
-0.25
9.53
0
-0.03
13
±0.5
3.175
0
-0.02
3.175
0
-0.02
1.57
±0.2
●
Standard Model Nos.
Bushingmount type:
With lug terminals:
12HHP-10E
With pin terminals for p.c. board:
12HHP-10EP
Servomount type:
12HHPS-10E
Model 12HHPS-10E
(Servomount)
Model 12HHP-10E
(Bushingmount)
●
Standard Dimensions
Note: Servomount type with pin terminals for p.c. board is also available.
Note: 1. 1 pc. each inner teeth washer and hex nut are attached.
2. Please process the mounting hole on the panel to be mounted with
this potentiometer by the diameter of 7.14mm .
■Bushingmount type
●
With lug terminals
●
With pin terminals for p.c. board
■Servomount type
Terminal Holes Layout
Hybrid
Glass-Filled Nylon
Bushingmount Rear LidHousingShaft
(Stainless Steel)
+
0.05
0