http://www.sapido.com.tw/ 1 User Manual v1. 0.
Table of Contents Table of Contents ........................................................................................................................ 2 FCC Caution ............................................................................................................................... 5 Chapter 1 Introduction ........................................................................................................ 7 1.1 Product Appearance .......................................................
4.4 Firmware Upgrade ............................................................................................ 36 4.4.1 Auto upgrade ............................................................................................ 37 4.4.2 Manual upgrade ........................................................................................ 37 4.5 DoS ................................................................................................................... 37 4.6 VPN Server .................
5.6 VPN Server ....................................................................................................... 65 5.7 Firewall ............................................................................................................. 65 5.7.1 DoS ........................................................................................................... 65 5.5.2 QoS .............................................................................................................. 65 5.5.
FCC Caution FCC Part 15.19 Caution: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including i nterference that may cause undesired operation 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3.
of the Member States relating to Electromagnetic Compatibility” (89/336/EEC; 92/31/EEC; 93/68/EEC) http://www.sapido.com.tw/ 6 User Manual v1. 0.
Chapter 1 1.
Chapter 2 System and Network Setup The BRF70N is an easy to setup and wireless device for various application and environment, especially for large installs such as hotels, offices space, warehouses, hot-spots and more. To begin with BRF70N , you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles on your system. Internet Account for XDSL/Cable Modem One Ethernet (10/100mbps) network interface card.
parameters, so it can work properly in your network environment. Before you connect to the wireless router and start configuration procedures, your computer must be able to get an IP address from the wireless router automatically (use dynamic IP address). If it’s set to use static IP address, or you’re unsure, please follow the below instructions to configure your computer with dynamic IP address: If the operating system of your computer is…. Windows 2000 Windows XP Windows Vista/Win7 2.3.
2.3.2 Windows XP 1. Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click “Properties”. 2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ 10 User Manual v1. 0.
2.3.3 Windows Vista / Windows 7 1. Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select “Properties”. Local Area Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”. 2.
2.4 Router IP Address Lookup After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop: Input “cmd”, and then click “OK”. http://www.sapido.com.tw/ 12 User Manual v1. 0.
Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default Gateway” (In this example, the gateway IP address of router is 192.168.1.1) NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with “169.x.x.x”, please recheck network connection between your computer and router, and / or go to the beginning of this chapter, to recheck every step of network setup procedure. 2.4.
Users can set or change user name and password used for accessing the web management interface in this section. Input User Name and New Password, then input Confirm Password again. Chapter 3 Internet Connection This Chapter describes how to setup BRF70N to the internet. The BRF70N is delivered with the following factory default parameters. Default IP address: 192.168.1.1 Default IP subnet mask: 255.255.255.0 Web login user name: admin http://www.sapido.com.tw/ 14 User Manual v1. 0.
Web login password: admin 3.1 Using as a broadband router Open a Web browser, and enter http://192.168.1.1 (Default Gateway) into the blank. Enter the User name and Password into the blank and then click Login. The default values for User Name and Password are admin (all in lowercase letters). Status page Download pdadd Logout 3.2 Home button menu http://www.sapido.com.tw/ 15 User Manual v1. 0.
Click Home button icon to enter MENU as below. Item Description Internet Setup There are several different method to access Internet，PPPoE、 DHCP、Static IP、PP TP 、L2TP 、WiFi ISP AP（switch to AP mode） If a router is already set at the house, and you want to make the wireless LAN communication WiFi AP（switch to WiFi AP mode） When you connect to the internet wirelessly through PC and wireless device without wireless LAN function equipped. Status You could check WAN, LAN, Client net work in status.
VPN Server PPTP/L2TP general setup introduction. NAT Management There are port forwarding and DMZ function Remote management This page allow you to access the GUI on WAN. Advance Setup Advance setting menu Time Zone You can maintain the system time by synchronizing with a public time server over the Internet. Factory Default You could reset the current configuration to factory default. Reboot This function is used to reboot Logout This page is used to logout. http://www.sapido.com.
3.3 Internet Setup Click Internet Setup icon to enter WAN setup as below. The Int ernet Setup is depended on the servic e that you contract with the provider. The BRF70N provides five selections for the Internet Mode type, PPPoE, DHCP, Static IP , PPTP and L2TP and WiFi ISP. Check with your ISP if you don’t know the WAN type. http://www.sapido.com.tw/ 18 User Manual v1. 0.
3.3.1 PPPoE Item Description User Name Input your us er name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. 3.3.2 DHCP http://www.sapido.com.tw/ 19 User Manual v1. 0.
Item Description MAC type Select "Universal” or “Specific" Universal：clone controller PC mac address as BRF70n WAN mac address Specific：use BRF70n itself mac address Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/ 20 User Manual v1. 0.
3.3.3 Static IP Item Description IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Gateway Input ISP Default Gateway Address. DNS Input DNS information which is provided by your ISP Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. 3.3.4 PPTP http://www.sapido.com.tw/ 21 User Manual v1. 0.
Item Description Addre ss Mode Select "Dynamic" or "Static" IP Address Input your IP address or domain name Gateway Input ISP Default Gateway Address. Server IP Address Input your server IP address provided by your ISP. know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. 3.3.5 L2TP Item Description Addre ss Mode Select "Dynamic" or "Static" IP Address Input your IP address or domain name Gateway Input ISP Default Gateway Address. Server IP Address Input your server IP address provided by your ISP. know, please check with your ISP. User Name Input PPTP account provided by your ISP.
3.3.6 WiFi ISP BRF70n WAN get IP address from other wireless AP and LAN/Wireless LAN client get IP from BRF70n. Item Description Survey List all available wireless AP Pre-Shared Key Input the wireless AP key which you want to connect Extend SSID Provide SSID for wireless client which want to connect to BRF70n Encryption Select wireless encryption type form the drop-down list. 3.
Item Description Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. Wireless AP Turn on/ off wireless 3.5 WiFi AP（ switch to WiFi AP mode） When you connect to the internet wirelessly through PC and wireless device without wireless LAN function equipped. This mode does not support WAN、DHCP、NAT、 DDNS、QoS、Firewall、Static/Dynamic route、VPN Server features. http://www.sapido.
http://www.sapido.com.tw/ 26 User Manual v1. 0.
Chapter 4 4.1 GUI Function Setup Status You could check WAN, LAN, Client net work in status. WAN Configuration http://www.sapido.com.tw/ 27 User Manual v1. 0.
LAN Configuration http://www.sapido.com.tw/ 28 User Manual v1. 0.
Client Configuration Allow or block client to access internet 4.2 Parental Control Parental Control provide URL Filtering and MAC Filter Schedule for setup 4.2.1 URL Filtering URL Filtering is used to restrict users to access specific websites in internet http://www.sapido.com.tw/ 29 User Manual v1. 0.
Item Description Enable URL Filtering Please select Enable MAC Filtering to filter MAC addresses URL Address Please enter the MAC address that needs to be filt ered. Apply Click on Apply to save the setting data. Current Filter Table It will display all ports that are filt ering now. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delet e all items in this table. Notes: This function will not be in effect when the Virtual Server is enabled.
Item Description Enable MAC Filtering Please select Enable MAC Filtering to filter MAC addresses. 4.2.3 Wireless Schedule Wireless available schedule, this page allows you setup the wireless schedule rule. Please do not forget to configure systeim before enable this feature http://www.sapido.com.tw/ 31 User Manual v1. 0.
4.3 Office Control Office control provide Multiple AP 、Wireless Access Control、IP Filtering、IP Binding、QoS 4.3.1 Multiple AP http://www.sapido.com.tw/ 32 User Manual v1. 0.
The BRF70n can register up to 4 SSIDs (wireless LAN group). It can be used as if there are multiple wireless LAN access points with one product. Item Description Enable Enable or disable the service. SSID Enter the SSID Data Rate Select the data transmission rate. Acce ss Enable this function can let clients use two access types: a. LAN+WAN: the client can access to the Internet and access in the router’s GUI. b. WAN: the client can only access to the Internet.
4.3.3 IP Filtering When enabled, LAN clients are blocked / filtered from accessing the Internet based on their IP addresses Item Description Enable IP Filtering Please select Enable IP Filtering to filter IP addresses. Local IP Address Please enter the IP address that needs to be filtered. Protocol Please select the protocol type of the IP address Apply Click on Apply to add the setting data Current Filter Table It will display all ports that are filt ering now.
Item Description Enable Static DHCP Select enable to use Static DHCP function IP Address Please enter IP address to limit MAC addre ss Please enter MAC address to limit Static DHCP Li st It will display all IP and MAC address you made. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delet e all items in this table. 4.3.5 QoS The QoS can let you classify Internet application traffic by source/destination IP address and port number.
Item Description Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port. Manual Uplink Speed Set the uplink speed by manual to assign the download or upload bandwidth by the unit of Kbps. Manual Downlink Speed Set the downlink speed by manual to assign the download or upload bandwidth by the unit of Kbps.
This function can upgrade the firmware of the router. There are two methods for user upgrade firmware: Auto upgrade and Manual upgrade. Caution: To prevent that firmware upgrading is interrupted by other wireless signals and causes failure. We recommend users to use wired connection during upgrading. Note : The firmware upgrade will not remove your previous settings. 4.4.1 Auto upgrade It provide auto detect new firmware from Internet, and user can select to upgrade new version or not. 4.4.
Home: Item Description Home Check “ Home” to enable DoS function for prevention. You also can check “No Prevention” to disable DoS function. Enterprise: http://www.sapido.com.tw/ 38 User Manual v1. 0.
Item Description Enterprise Check “Enterprise” to enable DoS function for prevention. You also can check “No Prevention” to disable DoS function. 4.6 VPN Server The VPN Server function providing PPTP/L2TP mode are designed to allow users to an external network device / computer and office local area network to establish a secure network connection. And User can safe login office local area network and access to personal documents, files Sharing and other resources.
Item Description Enable Setting Check this option, will start the VPN Server feature. Connection Type Provide PPTP or L2TP access connection type.
4.7.1 Virtual Server The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service port numbers (from the WAN port) to a particular LAN IP address. Item Description Enable Port Forwarding Select to enable Port Forwarding service or not. Addre ss Specify the IP address which receives the incoming packets. Protocol Select the protoc ol type. Public Port Range Enter the port number, for example 80-80.
All will delet e all items in this table. Please find the following figure to know that what the virtual server is. The web server is located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP. 4.7.2 DMZ The DMZ feature allows one local user to be exposed to the Internet for special-purpose applications like Internet gaming or videoconferencing. When enabled, this feature opens all ports to a single station and hence renders that system exposed to intrusion from outside.
4.8 Remote Management This page allows you to access the GUI on WAN. Item Description HTTP Connection Port Users can access GUI by this port，default is 80 Enable Web Server Access on WAN Allow user access GUI from WAN side 4.9 Time Zone Users can select time zone and synchronize the local clock on the router. Item Description Time Zone Select Please select the time zone. 4.10 Factory Default You could reset the current configuration to factory default. http://www.sapido.com.
4.11 Reboot This function is used to reboot 4.12 Logout This page is used to logout http://www.sapido.com.tw/ 44 User Manual v1. 0.
Chapter 5 5.1 Advance Setup Internet Mode 5.1.1 Internet Setup Please refer Internet Setup 5.1.2 AP（switch to AP mode） Please refer AP 5.1.3 WiFi AP（switch to WiFi AP mode） Please refer WiFi AP 5.1.4 WiFi ISP Please refer WiFi ISP 5.2 IP Config 5.2.1 WAN 5.2.1.1 PPPoE http://www.sapido.com.tw/ 45 User Manual v1. 0.
Item Description User Name Input your us er name provided by your ISP. please check with your ISP. Password Input the password provided by your ISP. Service Name Input the service name provided by your ISP. Connection Type Three types for select: Continue s, Connect on Demand, and Manual. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually. DNS Select Attain DNS Automatically.
Save & Apply 5.2.1.2 Click on Save to save the setting dat e, the Apply button for execute current configuration. DHCP Item Description Host Name You can keep the default as the host name, or input a specific name if required by your ISP. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually. DNS Select Attain DNS Automatically.
Item Description IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Gateway Input ISP Default Gateway Address, . MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually. DNS Input DNS information which is provided by your ISP Clone Mac Address Some ISPs require MAC address registration.
Item Description Server IP Address Input your server IP address provided by your ISP. know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address" Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration. 5.2.1.5 L2TP Item Description Server IP Address Input your server IP address or Host Name provided by your ISP. If you don’t know, please check with your ISP.
ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address" Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration. 5.2.2 LAN Use this page to set up the local IP address and subnet mask for your router.
and ex pired time. 192.168.1.200. The default range is 192.168.1.100 - DHCP Lease Time IP avaliable time Static DHCP Please refer IP Binding Domain Name The name of device 802.1d Spanning Tree IEEE 802. 1d Spanning Tree Protocol (STP) is a link layer network protocol t hat ensures a loop-free topology for any bridged LAN. The main purpos e of S TP is to ensure that you do not create loops when you have redundant paths in your net work. Loops are deadly to a network.
DynDNS, TZO, ChangeIP, Eurodns, OVH, NO-IP, ODS, Regfish embedded in BRF70N . User Name/Email User name is used as an identity to login Dynamic-DNS service. Password/Key Password is applied to login Dynamic-DNS servic e. Save & Apply Click on “Save” to save the setting data. The “A pply” button can execute current configuration 5.3 IPv6 Config Item http://www.sapido.com.tw/ Description 53 User Manual v1. 0.
Origin Type SLAAC、DHCPv6、IP。Please check ISP to get correct type WAN Link Type PPPoE、IP PPPoE Use IPv4 PPPoE account and password to do IPv6 connect Child Prefix Address Check ISP to get this data Static IP Check ISP to get IP address and default gateway IP address Router Name Router domain DNS v6 Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 5.4 Wireless 5.4.
Item Description Di sable Wireless Turn off the wireless service. Band Select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). Mode Select the mode. It has 3 modes to select: (AP, Client, WDS, AP+WDS). http://www.sapido.com.tw/ 55 User Manual v1. 0.
Multiple AP: Please check Section 4.1.2.1. * In Wi-Fi AP mode only support Client mode. Network Type Infrastructure：one of the two methods for connecting to wireless networks with Wi-Fi enabled devices such as laptops, Pda’s I-phone etc. These devices are connected to wireless network with the help of Access point (AP). Wireless Access Points are usually routers or switches which are connected to internet by Ethernet port.
Item Description Fragment Threshold To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is 256-2346, and default length is 2346. RTS Thre shold This value should remain at its default setting of 2347. The range is 0~2347. Should you encounter inconsistent data flow, only minor modifications are recommended. If a net work packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be enabled.
Short GI Users can get better wireless transmission efficiency when they enable this function. WLAN Partition Shut down th e communication betw een th e connected wireless LAN de vices. If you set up as "Ena ble d", devices connected with the router, such as a pr inte r, wi ll not be a ble to use. Default Sett ing: "Disab led " 20/40MHz Coexist Config ure 2 0/40 MHz coe xistin g scheme. If yo u set u p as "Ena ble d", "20 MHz" and "40 MHz" w ill coexist. Normall y use as "Disabl ed".
wir el es s LA N s ec u rit y, c on fig u re t h e c om mo n e nc ry pt ed k ey (W E P K ey ) f or ac c es s p oint an d wi r eles s LA N ha nds et . W E P k ey lengt h a re " 6 4b it " , " 128 bit " , a nd " 2 5 6bit " ( This pr od uc t c or res po nds up t o 12 8bit ), la rg er t he va lu e is , mor e t h e c h ar ac t e r c a n b e s et , a nd enc ry pt i on s t r en gt h will en ha nc e d.
connect. PBC model, in which the user simply has to push a button, either an actual or a virtual one, on both WPS devices to connect. BRF70n WPS only support no encryption and WPA2 Please follow instructions below to enable the WPS function. 1. Setup Wireless LAN with WPS PIN : (1). Get the WPS PIN number from wireless card and write it down. (2). Fill in the PIN number from the wireless card in Client PIN Number field, and then click “Start PIN”. (3).
(4). Wireless dongle should connect to BRF70n 2. Start PBC: (1). Press the BRF70n WPS button and wait for WPS LED blinking (2). Press the dongle WPS button (3). Wireless dongle should connect to BRF70n 5.4.6 WDS When selected in the Basic Settings page and enabled here, Wireless Distribution System (WDS) enables the router to be used as a wireless bridge. Two Wireless-N Routers in bridge mode can communicate with each other through their wireless interfaces.
Please check the MAC address Enable WDS function from the page – “WDS Setting”, and then fill in the MAC address of Router_B. Click Apply Changes to save the setting data. http://www.sapido.com.tw/ 62 User Manual v1. 0.
Select encryption for security Rout er_B mac address The WDS AP List will show the WDS device MAC address. Router_B： Setup Router_B WDS. Select encryption for security Rout er_A mac address http://www.sapido.com.tw/ 63 User Manual v1. 0.
Router_B LAN PC will get IP address from Router_A. If you failed the WDS setting, please check you setting with refer to the list below. Wireless Mode LAN IP Address Router_A AP+WDS Set the same segment as the router B(Note 1) Router_B WDS Set the same segment as the router_A (Note 1) Security Example :192.168.1.1 Set the same security as Rout er_B Enable Example :192.168.1.
5.6 VPN Server Please refer VPN server 5.7 Firewall 5.7.1 DoS Please refer DoS 5.5.2 QoS Item Description Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port. Automatic uplink speed Check the Automatic uplink speed. http://www.sapido.com.tw/ 65 User Manual v1. 0.
Manual Uplink speed Input uplink bandwidth manually Automatic downlink speed Check the Automatic downlink speed. Manual Downlink speed Input downlink bandwidt h manually Addre ss Type Set QoS by IP Address or MAC address Local IP Address Set local IP Address if the address type is by IP Address MAC Addre ss Set MAC Address if the address type is by MAC Address Mode Select Guaranteed minimum bandwidth or Restricted maximum bandwidth Uplink Bandwidth Key in the bandwidth.
IP: 192.168.1.x Port: 80-80 5.5.4 IP Filtering Please refer IP Filtering 5.5.5 Mac Filter Schedule Please refer Mac Filter Schedule 5.5.6 URL Filtering Please refer URL Filtering 5.5.7 IP Binding Please refer IP Binding 5.5.8 VLAN http://www.sapido.com.tw/ 67 User Manual v1. 0.
Item Description Forwarding Rule Bridge or NAT mode Tag Add VLAN tag to packet VID Set VLAN ID（1~ 4096） Priority It indicates the frame priority level. Values are from 0 (best effort) to 7 (highest); 1 represents the lowest priority CIF Enable or Disable CIF 5.6 System This section including Wake on LAN, Change Username/Password, Upgrade Firmware, Profiles Save, Remote Management, Time Zone, UPnP, Route Setup, VPN Passthrough, and Wan Type Auto Detection.
5.6.4 Change User name/Password Users can set or change user name and password used for accessing the web management interface in this section. Input User Name and New Password, then input Confirm Password again. 5.6.5 Upgrade Firmware Please refer Firmware Upgrade 5.6.6 Profiles Save Users can create a backup file that contains current router settings. This backup file can be used to restore router settings. This is especially useful in the event you need to reset the router to its default settings. 1.
(2). Please click “Save” to save the configuration to your computer. (3). Select the location which you want to save file, then click Save. 2. Load configuration file (1). Tap “browse” and select configuration file then click Open http://www.sapido.com.tw/ 70 User Manual v1. 0.
(2). Click Upload to upload configuration file to BRF70N . (3). After 60 seconds, BRF70N will reboot automatically. 5.6.7 Remote Management Please refer Remote Management 5.6.8 Time Zone Users can synchronize the local clock on the router to an available NTP server (optional). To complete this setting, enable NTP client update and select the correct Time Zone. http://www.sapido.com.tw/ 71 User Manual v1. 0.
Item Description Time Zone Select Please select the time zone. Enable NTP client update Please select to enable NTP client update or not. Automatically Adjust Please select to enable Automatically Adjust Daylight Saving or not. Daylight Saving NTP Server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration. 5.6.
5.6.10 Route Setup Dynamic routing is a distance-vector routing protoc ol, which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for RIP is 15 Static routing is a data communication concept describing one way of configuring path selection of rout ers in computer networks.
Item Description Enable Static Route Enable or Disable dy namic route IP Address Destination IP address Subnet Mask Destination IP subnet mask Gateway Gateway IP address for destination Metric Metric number on router’s routing table Interface Static route rule for LA N or WAN interface 5.6.11 VPN Passthough Virtual Private Networking (VP N) is typically used for work-related net working. For VP N tunnels, the router supports IPSec, Pass-through, PPTP Pass-through, and L2TP Pass-through.
5.6.12 Wan Type Auto Detection http://www.sapido.com.tw/ 75 User Manual v1. 0.
Chapter 6 Q&A 6.1 Installation 1. Q: Where is the XDSL Router installed on the network? A: In a typical environment, the Router is installed between the XDSL line and the LAN. Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub (switch or computer). 2. Q: Why does the throughput seem slow? A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter.
3. How can I check whether I have static WAN IP Address? A: Consult your ISP to confirm the information, or check Network Configuration in BRF70N ’s Main Menu. 4. Will the Router allow me to use my own public IPs and Domain, or do I have to use the IPs provided by the Router? A: Yes, the Router mode allows for customization of your public IPs and Domain. 6.4 OS Setting 1.
5. Make sure none of the check boxes are selected and click on OK button. 6. Click on OK button. Netscape Navigator Users: 1. 2. 3. 4. 5. 6. 3. Click on Edit > Preferences > double-click Advanced in the Category window. Click on Proxies > select Direct connection to the Internet > click on OK button. Click on Edit again and then click on Preferences. Under category, double-click on Advanced and then click on Proxies. Select Direct connection to the Internet and click on OK button. Click on OK button.
6.6 Wireless LAN 1. Q: Why couldn’t my wireless notebook work on-line after checking? A: Generally, Wireless networks can sometimes be very complicated to set up, particularly if you're dealing with encryption and products from different vendors. Any number of variables can keep your workstations from talking to each other. Let's go over some of more common ones. For starters, verify that your router and your workstation are using the same SSID descriptions.
3. To see if radio interference is causing a problem, see if connection is possible when close to the Wireless Access Point. Remember that the connection range can be as little as 100 feet in poor environments. Q: Wireless connection speed is very slow. A: The wireless system will connect at highest possible speed, depending on the distance and the environment. To obtain the highest possible connection speed, you can experiment with following: 4.
6.7 Support 1. Q: What is the maximum number of IP addresses that the XDSL Router will support? A: The Router will support to 253 IP addresses with NAT mode. 5. Q: Is the Router cross-platform compatible? A: Any platform that supports Ethernet and TCP/IP is compatible with the Router. 6.8 Others 1. Q: Why does the router dial out for PPPoE mode very often? A: Normally some of game, music or anti-virus program will send out packets that trigger the router to dial out, you can close these programs.
Chapter 7 Appendices 7.1 Operating Systems 1. Microsoft：Windows 2000, XP, Vista, Windows 7. 2. Apple：Mac OS X 10.4.7, Leopard and the following related versions. 3. Linux：Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions. 7.2 Browsers 1. Internet Explorer ver. 6 and 7 and the following related versions. 2. FireFox ver. 2.0.0.11 and the following related versions.3. 3. Safari ver. 3.04 and the following related versions. 7.
