User's Manual
URD1
– OTL 5696.1–
022
/ 72740 Edition 0.4
HILONC-
3GPS
APPLICATION
NOTE
End
Product
Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that
20 cm may be maintained between the antenna and users. The final end product must be labeled in a
visible
area
with
the
following:
“Contains
FCC
ID:
VW3HILONC-3GPS
”
”
Contains IC:
9140A-HILONC-3GPS
”
The grantee's FCC ID/IC ID can be used only when all FCC/Canada compliance requirements are met.
Plaque
signalétique
du
produit
final
Ce
module
émetteur
est
autorisé
uniquement
pour
une
utilisation
dans
un
dispositif
où
l'antenne
peut
être
installée
de
telle
sorte
qu'une
distance
de
20cm
peut
être
maintenue
entre
l'antenne
et
les
utilisateurs.
Le
produit
final
doit
être
étiqueté
dans
un
endroit
visible
avec
l'inscription
suivante:
"Contient
des
IC:
9140A-
HILONC-3GPS".
Manual
Information
To
the
End
User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove
this
RF
module
in
the
user’s
manual
of
the
end
product
which
integrates
this
modu
le.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel
d'information
à
l'utilisateur
final
L'intégrateur
OEM
doit
être
conscient
de
ne
pas
fournir
des
informations
à
l'utilisateur
final
quant
à
la
façon
d'installer
ou
de
supprimer
ce
module
RF
dans
le
manuel
de
l'utilisateur
du
produit
final
qui
intègre
ce
module.
Le
manuel
de
l'utilisateur
final
doit
inclure
toutes
les
informations
réglementaires
requises
et
avertissements
comme indiqué dans ce manuel.
This device has been designed to operate with a dipole antenna have a maximum gain of [0.6] dB. Antenna
having
a
higher
gain
is
strictly
prohibited
per
regulations
of
Industry
Canada.
The
required
antenna
impedance
is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference
to
other
users,
the
antenna
type
and
its
gain
should
be
so
chosen
that
the
equivalent
isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This
radio
transmitter
(IC:
9140A-HILONC-3GPS
/
Model:
HiLoNC-3GPS
)
has
been
approved
by
Industry
Canada
to
operate
with
the
antenna
type,
maximum
permissible
gain
and
required
antenna
impedance
for
each
antenna type indicated. Antenna types not included in this user’s manual, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Ce
dispositif
a
été
conçu
pour
fonctionner
avec
une
antenne
ayant
un
gain
maximal
de
dipole
antenne
avec
dB
[0.6]. Une antenne à gain plus élevé est strictement interdite par les règlements d'Industrie Canada.
L'impédance d'antenne requise est de 50 ohms.
Note d’étude / Technical document :
01/08/20111
-
Page
39
/
41