SAGEM F@st™ 908 / 948 Ethernet/USB Combo ADSL Modem Installation Guide Reference: 251 605 322 ed.
TM SAGEM F@st 908 / 948 Installation Guide E closely follows all technical changes and continually strives to improve its products for the benefit of its customers. It therefore reserves the right to change its documentation accordingly without notice.
TM SAGEM F@st 908 / 948 Installation Guide Contents Pages 1. Overview of the SAGEM F@st™ 908 / 948 modems 5 1.1 Description 5 1.2 Choosing the connection interface 6 1.3 Contents of your ADSL pack 7 1.4 Prerequisites 8 2. Hardware installation 9 3. Installing the modem in Ethernet mode 11 3.1 Connecting the Ethernet interface 11 3.2 Installing the software 11 3.2.1 Encapsulation options in Ethernet mode (depending on versions) 12 4. Installing the modem in USB mode 13 4.
TM SAGEM F@st 908 / 948 Installation Guide Safety instructions 21 CE declaration 22 Appendix B - Technical specifications 23 Hardware specifications 23 Software specifications 25 PC, Mac and Linux compatibility 26 Default configuration 26 Appendix C - Glossary 27 4
TM SAGEM F@st 908 / 948 Installation Guide 1. Overview of the SAGEM F@st™ 908 / 948 modems 1.1 Description The SAGEM F@st™ 908 / 9481 modems are ADSL "Combo" modems with USB and Ethernet interfaces used to browse the internet at high speeds using an ADSL-compatible telephone line. Their function is to transmit the data between a computer (PC or Mac) connected by an Ethernet interface and an Internet Access Provider (IAP), via an ADSL link.
TM SAGEM F@st 1.2 908 / 948 Installation Guide Choosing the connection interface You can choose between the connection interfaces based on a number of criteria: • Interface not available: your computer may not have an Ethernet card or an Ethernet port. • USB devices already used (keyboard, mouse, etc). If you already have several USB devices, you are advised to use the Ethernet interface to ensure that your Internet connection will be set up in the best possible conditions.
TM SAGEM F@st 1.3 908 / 948 Installation Guide Contents of your ADSL pack Your SAGEM F@st™ 908 / 948 pack contains the following items: One SAGEM F@st™ 908 / 948 ADSL modem One mains adapter unit One RJ11 type ADSL line lead One cross-pinned UTP RJ45 type Ethernet cable One Type A / Type B USB cable One modem installation CD-ROM One CD-ROM for installing the PPPoE client software (optional) ADSL splitters (optional) Note: This list is not exhaustive.
TM SAGEM F@st 1.4 908 / 948 Installation Guide Prerequisites Telephone ¾ Telephone line supporting ADSL transmission. line side ¾ Internet access provider (IAP) subscription ¾ Installation of ADSL splitters on each telephone socket used by a terminal (telephone, DECT phone, fax, answering machine, etc).
TM SAGEM F@st 908 / 948 Installation Guide 2. Hardware installation To install your modem without any difficulty, please follow the steps below in number order. 1. Connect the ADSL splitters to your telephone sockets The ADSL splitters (or filters) let you make phone calls and use your ADSL line at the same time. ADSL filter ! All the sockets used by a telephone device must be fitted with an ADSL splitter.
TM SAGEM F@st 908 / 948 Installation Guide 2. Power up your modem For this, use the power supply unit supplied with your modem2 When the modem is powered up, the PWR LED lights. 3. Link your modem to your telephone line The line lead supplied in your pack should connect the modem to the connector provided on your splitter or to a telephone network adapter. When the modem is linked to the telephone line, ADSL synchronization follows automatically. The ADSL LED is on permanently.
TM SAGEM F@st 908 / 948 Installation Guide 3. Installing the modem in Ethernet mode For more details on this installation procedure, refer to the SAGEM F@stTM 908 / 948 Ethernet Interface Reference Manual (see CD-ROM / Reference Manual - Ethernet Interface). 3.1 Connecting the Ethernet interface For this, use the cross-pinned Ethernet cable supplied with your modem. When the modem is connected to your computer, the Ethernet detection LEDs on your modem and your Ethernet card will light. 3.
TM SAGEM F@st 908 / 948 Installation Guide ¾ Select your country of residence (depending on model ). ¾ Choose your Internet Access Provider in the suggested list. Once the installation is done, you can go to the next stage. 3.2.1 Encapsulation options in Ethernet mode (depending on versions) The encapsulation parameters are automatically set up, when the Internet Access Provider is choosen in the list offered by the installation software.
TM SAGEM F@st 908 / 948 Installation Guide 4. Installing the modem in USB mode ! You must run the installation CD-ROM before connecting the USB cable to your computer. For more details on this installation procedure, refer to the reference manual SAGEM F@stTM 908 / 948 USB interface (see CD-ROM / Reference Manual - USB Interface). 4.1 Installation of the software In Windows XP, for example: ¾ Insert the CD-ROM of the modem in your computer's appropriate drive and the screen opposite appears.
TM SAGEM F@st 4.1.1 908 / 948 Installation Guide Encapsulation options in USB mode (depending on versions) The encapsulation parameters are automatically set up, when the Internet Access Provider is choosen in the list offered by the installation software. Nevertheless, the possibility of set up parameters, related to an Internet Access Provider which would not already been listed, has been provided for.
TM SAGEM F@st 908 / 948 Installation Guide 5. Problem solving 5.1 Interpreting LED indications 5.1.1 LEDs visible on the modem cover LED ADSL PWR On steady ADSL synchronized Modem powered up Off No ADSL sync Modem not powered Blinking Trying to set up ADSL synchronization Not applicable 5.1.
TM SAGEM F@st 5.2 908 / 948 Installation Guide Problem solving in Ethernet mode 5.2.1 LEDs No modem power supply Flag Status Meaning Check that the modem is receiving power supply. Only the power supply unit supplied with the modem should be used. ADSL off PWR off Red Modem not powered Check that your PSU's electrical specifications are compatible with your mains electricity network. Lastly, uninstall then reinstall the BridgeMon application.
TM SAGEM F@st 5.2.3 908 / 948 Installation Guide Absence of ADSL synchronization Firstly check that the conditions in the previous section are satisfied. LEDs Flag Corrective action Modem detected by your computer. ADSL off PWR on Status Red ADSL not synchronized Check the connection of your ADSL splitters. Each of your installation's telephone sockets should be fitted with an ADSL splitter. Check that the RJ11 type line lead supplied with your modem is connected to one of your sockets.
TM SAGEM F@st 5.2.4 908 / 948 Installation Guide Internet connection not possible Firstly check that the conditions in the previous section are satisfied. LEDs Flag Status Corrective action In PPPoE mode: Check that your PPPoE client software is correctly installed on your computer: ADSL on PWR on Green ADSL set up. In Windows XP, MacOS X, you can refer to Modem initialized section 4.1 of the SAGEM F@stTM 908 / 948 Ethernet Interface Reference Manual.
TM SAGEM F@st 5.3 908 / 948 Installation Guide Problem solving in USB mode 5.3.1 "ADSL" and "PWR" LEDs off ¾ Check that the USB lead is correctly connected to your computer (or to a HUB). ¾ Check that the drivers are correctly installed (refer to the reference manual SAGEM F@stTM 908 / 948 USB interface and the sections dealing with the status of the modem in Windows XP, MacOS 8.6-9.x or MacOS X).
TM SAGEM F@st 908 / 948 Installation Guide 20
TM SAGEM F@st 908 / 948 Installation Guide Appendix A - Safety instructions Safety instructions ! Environment READ THE FOLLOWING INSTRUCTIONS CAREFULLY ¾ The SAGEM F@st™ 908 / 948 must be installed and used inside a building (for desktop use). ¾ The ambient temperature must not exceed 45°C. ¾ The SAGEM F@st™ 908 / 948 must not be exposed to strong sunlight or to a strong heat source. ¾ The SAGEM F@st™ 908 / 948 must not be placed in an environment subject to significant steam condensation.
TM SAGEM F@st 908 / 948 Installation Guide ¾ Use a readily accessible power outlet, near to the modem. The power lead is 2 m long. ¾ Arrange the power lead in such a way as to ensure that the modem's power supply cannot be disconnected accidentally.
TM SAGEM F@st 908 / 948 Installation Guide Appendix B - Technical specifications Hardware specifications Mechanical Dimensions Width : 85 mm Depth : 105 mm Thickness : 32 mm Weight 120 g Installation On desktop Power supply Mains Type : Wall-mounted adapter unit Class : II Mains voltage : 198 V - 264 V : 50 Hz / 60 Hz Output voltage : 12 VDC Absorbed power :<6W DC power input Voltage 5 V - 20 V Absorbed power # 2.5 W USB interface Data rate < 12 Mbit/s Standard USB 1.
TM SAGEM F@st 908 / 948 Installation Guide ETH interface Specification IEEE 802.3 Configuration Auto-negotiation 10/100BASE-T Half/Full Duplex Data rate 10/100 Mbit/s autosensing Range: 100m Connectors RJ45 - 8-pin Port : MDI type ADSL interface Transmission code DMT Standards supported ANSI T1.413 Issue 2 G.992.1 (G.DMT) - appendix A for SAGEM F@stTM 908 and appendix B for SAGEM F@stTM 948 G.992.2 (G.Lite) G.
TM SAGEM F@st 908 / 948 Installation Guide Operation Standard ETS300 019-1-3, class T3.2 Temperature -5° C to +45° C Relative humidity 5 to 85 % Pressure 84 hPa to 106 hPa (880 to 1060 mbar) Solar radiation 700 W/m² Mechanical environment Standard ETS300 019-1 Warehousing Class T1.2 Transport Class T2.3 Operation Class T3.2 Physical/chemical environment Standard ETS300 019-1 Warehousing Class T1.2 Transport Class T2.3 Operation Class T3.
TM SAGEM F@st 908 / 948 Installation Guide Encapsulation protocols in USB interface mode PPPoA VCMUX or LLC PPPoE VCMUX or LLC RFC 1483 Router / DHCP VCMUX or LLC RFC 1483 Bridge / DHCP VCMUX or LLC PC, Mac and Linux compatibility PC Windows 98 FE Windows 98 SE Windows 2000 Windows Millenium Windows XP Windows NT (only in Ethernet interface mode) Mac OS 8.6 OS 9.04, OS 9.1, OS 9.2 OS X (10.1 & 10.2) Linux Mandrake 8.2 to 9.0 RedHat 7.2 to 8.
TM SAGEM F@st 908 / 948 Installation Guide Appendix C - Glossary AAL5 ATM Adaptation Layer type 5 ADSL Asymmetric Digital Subscriber Line ARP Address Resolution Protocol ATM Asynchronous Transfer Mode BAS Broadband Access Server CO Central Office DHCP Dynamic Host Configuration Protocol DSLAM Digital Subscriber Line Access Multiplexer ETH Ethernet IP Internet Protocol IAP Internet Access Provider ISP Internet Service Provider LAN Local Area Network LLC Logical Link Control (Enc
TM SAGEM F@st 908 / 948 Installation Guide TCP Transmission Control Protocol UBR Unspecified Bit Rate UDP User Datagram Protocol USB Universal Serial Bus VC Virtual Channel VCI Virtual Channel Identifier VCMUX Encapsulation (without header) VP Virtual Path VPI Virtual Path Identifier WAN Wide Area Network 28
E Network Division s Le Ponant de Paris - 27, rue Leblanc - 75512 PARIS CEDEX 15 - FRANCE Tél. : +33 1 40 70 63 63 - Fax : +33 1 40 70 66 40 http://www.sagem.
