MORPHOACCESS TM Installation Guide MA1xx series MorphoAccessTM 100/110/120 November 2005 SK 0000034370 - 01
SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
CONTENTS INTRODUCTION 5 SAFETY INSTRUCTIONS 6 GENERAL DESCRIPTION 7 INSTALLATION PROCEDURE 10 STAGE 1 : DRILLING THE CHASSIS MOUNTING HOLES STAGE 2 : CABLE ENTRY HOLE LOCATION AND CHASSIS FIXATION STAGE 3 : CONNECTING THE COVER ASSEMBLY TO THE CHASSIS STAGE 4: CLOSING MORPHOACCESS™ 10 11 12 13 ELECTRICAL INTERFACE 14 TERMINAL BLOCK BOARD WIRING POWER SUPPLY CABLE WIEGAND OUTPUT WIRING DATA CLOCK OUTPUT WIRING COM RS485 SERIAL PORT ETHERNET WIRING OUTPUT RELAY TAMPER SWITCH 14 16 16 17 17 18 19
SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
INTRODUCTION Congratulations for choosing the SAGEM MorphoAccess™1 Automatic Fingerprint Recognition Terminal. MorphoAccess™ provides an innovative and effective solution for access control applications using Fingerprint Verification or/ and Identification. Among a range of alternative biometric techniques, the use of finger imaging has significant advantages : each finger constitutes an unalterable physical signature which develops before birth and is preserved until death.
SAFETY INSTRUCTIONS The installation of this product should be made by a qualified service Person and should conform to all local codes. It is strongly recommended to use a class II power supply at 12 V ±5% and 0.5 A. min according with Safety Electrical Low Voltage (SELV). The 12 V power supply cable length should not exceed 5 meters.
GENERAL DESCRIPTION Optical Sensor Contactless Card reader ( depending of the versions) Terminal Block Tamper switch Trap door Power supply cable Mounting keyholes Cable entry SK-0000034370-01 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
MorphoAccess™ supplies : 1 Cover assembly 1 Chassis 1 Trap door 2 screws for cover fixation 1 secured screwdriver Torx 20 1 secured screw for trap door fixation Qty 1 Cover assembly 1 Chassis 8 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
1 Trap door 2 Screws for cover fixation into the chassis. 1 Secured screw for trap door fixation 1 Secured screwdriver Torx 20 In order to proceed to MorphoAccess installation , you’ll need a standard 2,5mm screwdriver. SK-0000034370-01 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
INSTALLATION PROCEDURE Stage 1 : Drilling the chassis mounting holes (a) Screw : 4 mm (b) Screw : 3 mm I. For choice, drill the 4 corners holes (a) for the screws for the mounting keyholes so that the cable entry is in a suitable position for your cabling, using the dimensional drawing above. II. In case of electric plug connections , MorphoAccess™ terminal may be installed directly on US or European plugs , with some of the 5 holes (b). So, drill the needed holes. 10 SAGEM Défense Sécurité document.
Stage 2 : Cable entry hole location and chassis fixation Cable entry Cable entry I. Pass the all connecting cables through the 2 cable entry. Be sure during manipulation that power supply from electric source is off. II. Fit the screws chassis fixation. The mounting screws must be 4 mm diameter maximum for corner place (a) and 3 mm diameter maximum for other places (b). Small head screws are required. SK-0000034370-01 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
Stage 3 : Connecting the cover assembly to the chassis ( II ) Screw chassis fixation Screw chassis fixation I. Pass all connecting cable into cover entry holes. II. Put the cover assembly into the chassis hanging III. Fit the 2 screws chassis fixation , supplied with MorphoAccess™ IV. Connect cables to terminal blocks (see the detailed instructions in the following sections) 12 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
Stage 4: Closing MorphoAccess™ (I) ( II ) I. Push up the trap door along the cover assembly II. Fit the M4x20 assembly secured screw ( use screwdriver Torx 20S supplied with MorphoAccess™ ) SK-0000034370-01 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
ELECTRICAL INTERFACE Terminal block board wiring Various interfaces 14 USB master connector Power supply source SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 USB 15 Pin 1 TR- / D1 Out Wiegand D1 or RS485 TX/RX- or CLK Pin 2 TR+ / D0 Out Wiegand D0 or RS485 TX/RX+ or Data Pin 3 LED1 In Wiegand LED1 Pin 4 LED2 In Wiegand LED2 Pin 5 GND Pin 6 Relay C0 Contact Relay 0 Pin 7 Relay C1 Contact Relay 1 Pin 8 TSW0 Tamper switch Contact 0 Pin 9 TSW1 Tamper switch Contact 1 Pin 10 GND Ground for Ethernet Interface (LAN 10/100 Mbps) Pin 11 RX- Receive negative Ethernet Pin 12 RX+ Receive
Power supply cable 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin 15 +12V Positive 12 Volts , power supply. Pin 16 GND Ground power supply. 15 16 Power supply : Must be conformed to CEE/EEC EN60950 standard 12 Volts ± 5% (regulated) 0.5 Amp. It could be coming from 12 Volts Wiegand power supply , conforms to the Security Industry Association's Wiegand standard March 1995.
Data Clock output wiring 1 2 3 4 5 6 7 8 9 Pin 1 TR- / D1 Out Clock Pin 2 TR+ / D0 Out Data Pin 5 GND 10 11 12 13 14 15 16 15 16 Ground for Wiegand / RS485 / Dataclock The electrical interface is 5V TTL compatible.
Ethernet wiring 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin 10 GND Ground for Ethernet Interface (LAN 10/100 Mbps) Pin 11 RX- Receive negative Ethernet Pin 12 RX+ Receive positive Ethernet Pin 13 TX- Transmit negative Ethernet Pin 14 TX+ Transmit positive Ethernet 16 RJ 45 cabling recommendation : RJ45 plug pinout is compliant with 10 base T , IEEE802.3 Specification.
Output relay 1 2 3 4 5 6 7 8 9 10 11 Pin 6 Relay C0 Contact Relay 0 Pin 7 Relay C1 Contact Relay 1 12 13 14 15 16 Relay ratings 1 A at 30 VDC according to the safety extra low voltage requirements (42.4 VAC max, 60 VDC max) independently of the power supply. Tamper switch 1 2 3 4 5 6 7 8 9 10 11 12 Pin 8 TSW0 Tamper switch Contact 0 Pin 9 TSW1 Tamper switch Contact 1 13 14 15 16 Tamper-switch ratings 50 mA at 20 VDC max according to the safety extra low voltage.
USER INTERFACE MorphoAccess™ terminal works upon three principles : Access control with identification, access control with authentication, and proxy mode.
Recommendations Areas containing combustibles It is strongly recommended that you do not install your SAGEM MorphoAccess™ in the vicinity of gas stations, petroleum processing facilities or any other facility containing flammable or combustible gasses or materials. General precautions • Do not attempt to repair your SAGEM MorphoAccess™ yourself. The manufacturer cannot be held responsible for any damage/accident that may result from attempts to repair components.
Cleaning precautions A dry cloth should be used. Warning The manufacturer cannot be held responsible if the above recommendations are not followed or if the SAGEM MorphoAccess™ is incorrectly used. Biometrics Terminals Hot-Line To Access this service, please call us in order to get your login. Please send email rather call the hot-line. Email: hotline.biometrics@sagem.com Tel : + 33 1 34 30 39 19 (Monday to Friday, 9H00am to 6H00pm ) 22 SAGEM Défense Sécurité document.
APPENDIX 1 - FINGERPRINT PLACEMENT RULES To ensure a good quality contact of your finger on the terminal you must leave your finger on the sensor until sensor light is turned off. Area containing most of the information SK-0000034370-01 Fingerprint Placement Fingerprint Orientation Fingerprint Inclination Fingerprint Rotation SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
APPENDIX 2 - BIBLIOGRAPHY Configration Guide : MA1xx Series This guide gives all informations about terminal parameters. MorphoAccess Host System Interface Specifications Describes MorphoAccessTM communication protocol (Serial and Ethernet). MorphoAccess Remote Messages Specifications Complete specifications describing remote messages send during control (Wiegand, Dataclock, Ethernet and Serial).
APPENDIX 3 - DRILLING TEMPLATE Screw : 4 mm Screw : 3 mm SK-0000034370-01 SAGEM Défense Sécurité document. Reproduction and disclosure forbidden.
SAGEM Défense Sécurité Siège social : Le Ponant de Paris 27, rue Leblanc - 75512 PARIS CEDEX 15 - FRANCE Société anonyme à directoire et conseil de surveillance au capital de 36 405 229 € 562 082 909 RCS PARIS
