User's Manual

ManualsBrandsSAFEFLEET ManualsCamera & PhotoFocus-X2 Body-worn camera

FCC part 15B

Guidelines for Labelling and User Information for Devices Subject to Part 15

( from FCC 784748 D01 Labelling Part 15 &18 Guidelines v07)

Labelling Requirements for Part 15 Devices:

Verification

The specific labelling requirements for a device subject to the Verification procedure are

contained in Section 15.19(a). These labelling requirements are:

If the device is subject only to Verification, include a label bearing a unique identifier (Section

2.954) and one of three compliance statements specified in Section 15.19(a). If the labelling

area for the device is so small, and/or it is not practical to place the compliance statement on the

device, then the statement can be placed in the user manual or product packaging (Section

15.19(a)(5)). However, the device must still be labelled with the unique identifier (Verification).

Generally, devices smaller than the palm of the hand are considered too small for the ompliance

statement.

Certification

If the device is subject to Certification: (1) Section 2.925 contains information on identification

of the equipment; (2) include a label bearing an FCC Identifier (FCC ID) (Section 2.926) and (3)

include the appropriate compliance statement in Section 15.19(a). If the device is considered

too small and therefore it is impractical (smaller than the palm of the hand) to display the

compliance statement, then the statement may be placed in the user manual or product

packaging. However, the device must still be labelled with the FCC ID. If the device is

unquestionably too small for the FCC ID to be readable (smaller than 4-6 points), the FCC ID

may be placed in the user manual. However, it must be determined that the device itself is too

small – the label area allocated to the FCC ID may not be reduced because of over crowded

identification of other product and regulatory information.

An electronic display of the FCC ID (see 9. Electronic Labelling below) may be used for

Certification of Section 15.212 modular transmitters and software defined radios (Section

2.944).

Declaration of Conformity (DoC)

The labelling requirements for a device subject to the DoC procedure are specified in Section

15.19(b). The label should include the FCC logo along with the Trade Name and Model Number,

which satisfies the unique identifier requirement of Section 2.1074 if it represents the identical

equipment tested for DoC compliance. For personal computers assembled from authorized

components, the following additional text must also be included: “Assembled from tested

components,” “Complete system not tested.” When the device is so small and/or when it is not

Summary of content (5 pages)

PAGE 1
FCC part 15B Guidelines for Labelling and User Information for Devices Subject to Part 15 ( from FCC 784748 D01 Labelling Part 15 &18 Guidelines v07) Labelling Requirements for Part 15 Devices: Verification The specific labelling requirements for a device subject to the Verification procedure are contained in Section 15.19(a). These labelling requirements are: If the device is subject only to Verification, include a label bearing a unique identifier (Section 2.
PAGE 2
practical to place the required additional text on the device, the text may be placed in the user manual or pamphlet supplied to the user. However, the FCC logo, Trade Name, and Model Number must still be displayed on the device (Section 15.19(b)(3)). Equipment certified as software defined radio may use a means that readily displays the FCC ID on an electronic display screen, instead of labelling the device (Section 2.925 (e)). 1.
PAGE 3
2. Accessory: Focus X2 body worn camera x 1pcs Single Office Dock x 1pcs USB cable x 1pcs 5V / 2.5A AC-DC Power Adapter x 1pcs 3. LCD Display Display the status of Operation/Bluetooth / Battery / WIFI / Storage capacity 4. Buttons Button Power button Power on / off SYNC button WIFI on/off Recording button Start / Stop video recording Fn function button User can set different function via config.
PAGE 4
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 5
- French:" Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement." The device has been tested and in compliance with SAR limits.