Installation Manual

ManualsBrandsSafari ManualsNew Products!V-Spec Snorkel to suit Nissan Navara D22 Dual Battery 2.5L Diesel

Page 1 of 8

SS726HF SAFARI V-SPEC SNORKEL

NISSAN D22 NAVARA (Dual Battery)

2.5L Turbo Diesel (YD25 Cti Engine)

01/11/2014

Parts List

ITEM

PART NO.

DESCRIPTION

QTY

425-133-000

BODY - SNORKEL (SS725HF)

000-135-400

3” AIR RAM ASSEMBLY

425-032-000

BRACKET - UPPER MOUNTING

000-002-100

BOLT - HEX - 6mm x 1.0 x 14mm (SEMS)

000-951-300

SCREW - S/T - 4.2mm x 16mm - S/S

000-960

INSERT - PLASTIC

000-110

STUD - 8mm x 1.25 x 25mm - S/S

000-311-300

WASHER - BODY - 8mm x 30mm - S/S

000-205-300

NUT - NYLOC - 8mm x 1.25mm - S/S

425-024-200

HOSE - AIR ENTRY

000-908

CLAMP - HOSE - 70/90mm - S/S

425-123-200

DUCT - AIR CLEANER INLET

000-130

STUD - 5mm x 0.8mm x 20mm - S/S

000-320-350

WASHER - BODY - 5mm x 15mm - S/S

000-221-300

NUT - NYLOC - 5mm x 0.8mm - S/S

000-918/B

CLAMP - HOSE - SIZE 48 (BLACK)

425-017-000

TEMPLATE - GUARD PANEL

Summary of content (8 pages)

PAGE 1
SS726HF SAFARI V-SPEC SNORKEL NISSAN D22 NAVARA (Dual Battery) 2.5L Turbo Diesel (YD25 Cti Engine) 01/11/2014 Parts List ITEM PART NO. DESCRIPTION 1 425-133-000 BODY - SNORKEL (SS725HF) 1 2 000-135-400 3” AIR RAM ASSEMBLY 1 3 425-032-000 BRACKET - UPPER MOUNTING 1 4 000-002-100 BOLT - HEX - 6mm x 1.0 x 14mm (SEMS) 3 5 000-951-300 SCREW - S/T - 4.2mm x 16mm - S/S 4 6 000-960 INSERT - PLASTIC 3 7 000-110 STUD - 8mm x 1.
PAGE 2
SS726HF SAFARI V-SPEC SNORKEL NISSAN D22 NAVARA (Dual Battery) 2.
PAGE 3
Align the guard panel template (Item 17) with the upper and rear edges of the LHS guard panel as shown. Tape the template to the guard panel with masking tape. Mark all hole positions, including guard mounted indicator relocation position (if guard mounted indicator fitted to vehicle) with a felt tip pen. Remove the template. 4 Drill a pilot hole for each of the marked hole positions. Use a 86mm diameter hole saw to drill the snorkel body outlet hole position.
PAGE 4
5 Apply Loctite 243 to each of the stainless steel mounting studs (Item 7) and install the studs finger tight into the snorkel body (Item 1) mounting inserts as shown. NEW ZEALAND INSTALLATIONS ONLY : Safari have developed 2 methods of Snorkel A pillar attachment, for the conventional method please proceed with the current document alternatively please see the link below for further instructions. www.safari4x4.co.nz/apillarmounting 6 Carefully install the snorkel body (Item 1) to the guard panel.
PAGE 5
8 Fasten the upper mounting bracket to snorkel body with hex bolts (item 4). Carefully position the snorkel body onto the guard, with the snorkel correctly positioned onto the guard panel and ‘A’ pillar, mark the 3 upper mounting bracket hole positions onto the plastic windscreen moulding (as shown). Remove the snorkel body. 9 Drill a 5.
PAGE 6
11 Fasten the upper mounting bracket (item 3) to the ‘A’ pillar with self-taping screws (item 5), refit the rubber wind lacing mould (making sure it clips back into position correctly). 12 Carefully install the snorkel body (Item 1) to the guard panel, align the snorkel body to the guard panel and upper mounting bracket. When correctly aligned, fasten the snorkel body to the guard panel with body washers (Item 8) and nyloc nuts (Item 9).
PAGE 7
14 Install the connecting duct to the inner guard panel, fasten into position through the standard inner guard panel holes with 5.0mm body washers (item 14) and 5.0mm nyloc nuts (item 15) as shown. 15 Apply a liberal amount of adhesive sealant to the air cleaner housing inlet and connecting duct, install the air cleaner housing and fasten with standard mounting hardware. Secure the connecting duct to air cleaner housing with self-taping screw (item 5).
PAGE 8
17 Install the black hose clamp (Item 16) loosely over the base of the air ram assembly (Item 2). Install the air ram assembly onto the snorkel body. Align the air ram assembly and tighten the black hose clamp (Item 16).