TALEA ALEA - ODEA SER SERVICE M MANUAL Revision n 3 / January 2009 All parts of this document are the property of Saeco International Group. All rights reserved. The manufacturer shall not accept responsibility for possible errors or omissions in this document. Any reproduction or use by third parties is prohibited without the prior written approval of the manufacturer or through an agreement clause. Saeco International Group Rev. 03 / Jan.
Table of contents Page 1. 1.1 1.2 1.3 1.4 1.5 1.6.1 1.6.2 Introduction Documents required Tools and resources Materials Safety precautions Model overview External appliance components Internal appliance components 2. Technical specifications 1 3. 3.1 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 3.2 3.3 Operating User interfaces Odea Go Odea Giro, Talea Giro Talea Giro Plus Talea Ring, Ring Plus Talea Touch Use, cleaning, maintenance Messages - Troubleshooting 1 2 3 3 4 8 12 13 4. 4.1.1 4.1.2 4.2 4.3 4.4 4.5 4.
Table of contents Page 4. 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 Functional principles Water level detection of fresh water tank Limescale filter Water level detection of residual water tray “Empty dreg drawer” message Descaling request Electronical configuration (DIP-switch setting) Cup lift Milk Island 5. 5.1.1 5.1.2 5.2.1 5.2.2 5.3.1 5.3.2 5.
Table of contents 7. 7.7 7.8 7.9 7.10 7.11 7.12 7.13 Disassembly Solenoid valve / multi-way valve Pump Hose connections (assembly) Coffee grinder Grinders Adjustment of coffee grinder Cup lift 8. Notes 9. Water system diagrams Odea Go Odea Giro Plus, Giro Talea 10. Wiring diagrams Odea Go Odea Giro Talea Giro Plus Talea Ring Talea Ring Plus Talea Touch Plus Saeco International Group up Page 6 7 7 9 10 11 12 1 Rev. 3 / Jan.
CHAPTER 1 INTRODUCTION Saeco International Group up Rev. 3 / Jan.
TALEA / ODEA - LINE 1.1 01 INTRODUCTION Documents required The following documents are needed for repair work: • • Instruction booklet for the related model Technical documentation for the related model 1.
01 INTRODUCTION 1.5.
TALEA / ODEA - LINE 1.6.1.
01 INTRODUCTION 1.6.2. TALEA / ODEA - LINE Internal appliance components Boiler Pump Unblocking filter Flowmetre Control board Power board Coffee grinder Multi-way valve (not odea Go) Electrical cup lift’s motor *Touch/Ring Plus only Page 4 / 4 Rev. 03 / Jan.
CHAPTER 2 TECHNICAL SPECIFICATIONS Saeco International Group Rev. 3 / Jan.
TALEA / ODEA - LINE 02 TECHNICAL SPECIFICATIONS Technical specifications Connection values / power consumption: Temperature control: 230 V~, 50/60 Hz, 1500 W Safety equipment: 2 safety thermostats, can resist 175°C Temperature sensor (NTC, 20°C approx.
CHAPTER 3 OPERATING Saeco International Group Rev. 3 / Jan.
TALEA / ODEA - LINE 3.1. User interfaces 3.1.1 Odea Go 03 OPERATING “Appliance ready” LED: • Permanently on: The appliance is ready for use. • Flashing: The appliance has to finish the heating-up phase. “Empty dreg drawer” LED: • Permanently on: Empty the dreg drawer. The appliance must be switched on for this procedure. Control to set how much coffee is dispensed into the cup. Coffee dispensing key: • Flashing slowly: 1 coffee selected (key pressed once).
03 OPERATING 3.1.2 TALEA / ODEA - LINE Odea Giro,Talea Giro “Appliance ready” LED: • Permanently on: The appliance is ready for use. • Flashing: The appliance has to finish the heating-up phase. “Empty dreg drawer” LED: • Permanently on: Empty the dreg drawer. The appliance must be switched on for this procedure. Control to set how much coffee is dispensed into the cup. Coffee dispensing key: • Flashing slowly: 1 coffee selected (key pressed once).
TALEA / ODEA - LINE 3.1.3 03 OPERATING Talea Giro Plus “Appliance ready” LED: • Permanently on: The appliance is ready for use. • Flashing: The appliance has finished the heating-up phase. “Empty dreg drawer” LED: • Permanently on: empty the dreg drawer. The appliance must be switched on for this procedure. Control to set how much coffee is dispensed into the cup. Coffee dispensing key: • Flashing slowly: 1 coffee selected (key pressed once). • Flashing rapidly: 2 coffees selected (key pressed twice).
TALEA / ODEA - LINE 3.1.4 03 OPERATING Talea Ring, Ring Plus Go to customer menu coffee ....... aroma Activate steam function time Coffee start key Press once for 1 coffee Press twice for 2 coffees Press down longer = quantity programming Coffee product selection .
03 OPERATING TALEA / ODEA - LINE Main menu levels 1 beverage settings Dosage quantity Temperature Prebrewing 2 machine settings Language Water hardness Acoustic signal / alarm Filter alarm Rinsing Cup warmer (Ring Plus) Time setting (Ring Plus) 3 maintenance Aqua Prima Descaling Clean brewing unit 4 energy saving Switch-off time (standby) Timer (switching time) 5 special functions Restore settings (factory settings) Exit Cancel: Press the menu key several times until you see “cancel” in the dis
nu key long off medium high / dd/ i D 2.6 Cup warmer ** 24hr - am/pm On/Off 2.5 Rinsing Time format On/Off 2.4 Water filter alarm Hours Minutes On/Off 2.3 Signal alarms Time setting 1,2,3,4 On/Off 2.2 Water hardness 2.7 Clock setting ** Prebrew normal low Temperature +/- 8 languages Long press Short press Cup capacity 2.1 Language 1.1.Espresso 1.2. Coffee 1.3. Large coffee Customer menu table 1. Beverage settings 2.
3. Maintenance 4. Energy saving mode dd/mm/yy Date format Activate Activate filter Remaining water quantity 5.1 Restore settings immediately Time Turn off Restore settings, are you sure? Time On/Off 4.2 Timer setting ** Turn on 15 - 180 minutes 4.1 Switch-off time 4.3 Monday - 4.9 Sunday ** Carry out immediately Carry out immediately On/Off Filter status Remaining water quantity dd/mm/yyyy Date setting 3.3 Clean brewing unit 3.2 Descaling 3.
TALEA / ODEA - LINE 3.1.5 03 OPERATING Talea Touch To start: Press the “go to menu” key Beverage programming: Keep the relevant beverage key pressed show text 8:30 24/06/06 go to menu Scroll if menu point has several pages Back to previous menu point Back to main menu Save Confirm (activate functions) Exit menu 1.
03 OPERATING TALEA / ODEA - LINE Example, water hardness setting 1. main menu beverage settings machine settings time/date setting maintenance settings In the first main menu, select “machine settings” 1.2 machine settings language & display alert and acoustic setting cup - warming surface water settings Press the “water settings” key 1.2.4 water settings rinse water filter On Off water hardness . Press the “Water hardness” key 3/4 1.2.4.
. Main menu 1.1. Beverage setting 1.2. Machine settings Beverage settings Machine settings Time settings Water settings Heated cup holder Acoustic signals and alarms Language & display Espresso Coffee Large coffee Customer menu table 1.1.1. Espresso/ 1.1.2.Coffe/1.1.3.Large Coffee 1.2.1. 1.2.2. 1.2.3. 1.2.4. 3.1.
1. 2. Main menu Clock settings Maintenance settings Special settings 1.3. Clock settings 1.4. Maintenance settings 2.1. Special settings no/yes Cleaning cycle Descaling cycle Display lock Factory settings Release Product counter Yes/no Yes/no Reset Large coffee Coffee Espresso Machine on/off Time format Current date Date format after 15 minutes after 30 minutes after 1 hour after 3 hours Interval 1 Interval 2 Interval 3 Day settings Standby setting Date settings Time settings 1.3.2.
TALEA / ODEA - LINE 3.
03 OPERATING 3.3 TALEA / ODEA - LINE Messages - troubleshooting DISPLAY MESSAGE SHOWN INSTRUCTIONS FOR TROUBLESHOOTING Turn machine off and on to solve the problem Turn the appliance off and then back on after 30 seconds to resolve the fault. The problem requires the intervention of the Service Centre Insert the drip tray The coffee bean hopper lid must be closed to produce beverages.
CHAPTER 4 FUNCTIONAL PRINCIPLES Saeco International Group Rev. 3 / Jan.
TALEA / ODEA - LINE 4.1.1 04 FUNCTIONAL PRINCIPLES Odea Go water system Boiler 1 Caldaia Hot water / steam valve Rubinetto Water tank Serbatoio Turbina Flowmetre Valvola Overpressure Pompa EP5 sicurezza Pump valve Perno Caldaia conValve spillopin Gruppo Brewing unit Odea Go • • • • • • • Conventional water system Flowmetre - cup capacity / ventilation display Reciprocating piston type pump (13 - 15 bar) Overpressure valve (opening pressure 18 - 20 bar).
04 FUNCTIONAL PRINCIPLES 4.1.2 TALEA / ODEA - LINE Talea, Odea Giro water system Caldaia Boiler 1 Hot water / Rubinetto steam valve Talea series only Water tank Serbatoio Pump Pompa EP5 Flowmetre Turbina Overpressure Sistema di valve (steam sicurezza pipe) Milk Island Elettropilota Two-way valve Valvolavalve 1 Electrical scarico Valve pressure Valvola 2 reduction approx. 4bar 4 bar Valvolavalve 3 Coffee approx.
TALEA / ODEA - LINE 4.2. 04 FUNCTIONAL PRINCIPLES Solenoid valve / multi-way valve to hot water / steam valve Ventilation: from boiler Pin After the appliance is switched on, the electric valve opens, the pump is activated and the appliance is ventilated automatically.
04 FUNCTIONAL PRINCIPLES TALEA / ODEA - LINE to hot water / steam valve Pipe system pressure reduction: from boiler Pin The electrical valve opens to reduce the pressure in the pipe system: Each time hot water or steam is used Each time milk is frothed with the Milk Island.
TALEA / ODEA - LINE 4.4. 04 FUNCTIONAL PRINCIPLES Coffee cycle Main switch ON START STOP Timing Pulse (Dosage) Coffee grinder approx.
04 FUNCTIONAL PRINCIPLES 4.5. TALEA / ODEA - LINE Brewing unit’s gear mechanism With 2 microswitches MS2 2 MS1 1 MS 2 1 4.6. T (°C) Single micro The function is the same as with 2 microswitches. However, here a toothed gear with continuous pin is used and a single microswitch takes over the monitoring of both end positions.
TALEA / ODEA - LINE 4.7. 04 FUNCTIONAL PRINCIPLES SBS SBS - Saeco Brewing System - principle Controlling the flow speed that then influences the contact time between the coffee and water, changes the extraction and therefore the taste intensity and strength of the coffee. • Slower flow: strong extraction • Rapid flow: weaker extraction SBS / dispensing valve Turning the SBS control knob creates a back pressure in the brewing unit where the flow speed is regulated using a controllable cream valve.
04 FUNCTIONAL PRINCIPLES 4.8. TALEA / ODEA - LINE Coffee grinder Ceramic coffee grinder 6 4 1 2 3 4.9. V Two magnets (6) are built into the drive gear. A Hall sensor is mounted on the bottom side of the housing that sends 2 pulses to the electronics using two magnets per rotation.
TALEA / ODEA - LINE 4.10. 04 FUNCTIONAL PRINCIPLES Autodose - automatic dosing quantity control Autodose The appliances are fitted with an automatic dosage quantity adjustment from the following software versions: Type Software version with autodose Talea Touch ≥ V.01.08.14 Talea Ring Plus / Ring ≥ V.02.00.08 Talea Giro e Odea Giro / Go ≥ V01.02.
04 FUNCTIONAL PRINCIPLES 4.11. TALEA / ODEA - LINE Water level detection of fresh water tank “Low water” message (water reserve) Function: The water level is monitored using a capacitive sensor. This is fitted on the side of the machine at the height level of the lower third of the water tank. When the sensor communicates to the electronics that there is no water in the tank at its level, there is still a water reserve of 200 flowmetre pulses remaining for the current dispensing that will be completed.
TALEA / ODEA - LINE 4.13. 04 FUNCTIONAL PRINCIPLES Water level detection of residual water tray “Empty residual water tray” message Residual water tray Total capacity 4.14. Function: The residual water level is monitored using a capacitive sensor. The sensor is positioned approx. half way up the upper edge of the residual water tray. To ensure the best possible use of holding capacity, the sensor is positioned in the area of a shaft where its upper edge overlaps the sensor.
04 FUNCTIONAL PRINCIPLES 4.15. Descaling request “Descaling with limescale filter” message (appliances that have a display only) Flowmetre pulses Filter on Filter off Number of pulses 360° 1 rev 4.16. TALEA / ODEA - LINE The water hardness is set in the usual way by determining the regional water hardness. (1, 2, 3, 4).
TALEA / ODEA - LINE 4.17. 04 FUNCTIONAL PRINCIPLES Cup lift Electrical cup lift (Talea Touch and Ring Plus only) 3 6 Function: The sensors control an inching motor (3) in different rotating directions. A spindle (4) where the bottom end is attached flush with the cup plate (5), gets turned by the direction of motion of the motor: lifting or lowering. The end positions are monitored by two microswitches: upper end switch (6) and lower end switch (7). 2 5 1 4.18.
04 FUNCTIONAL PRINCIPLES TALEA / ODEA - LINE Electrical connection to the machine Pushbutton for connecting and disconnecting the Milk Island to/from the machine Hydraulic connection on the appliance for the incoming steam supply Escaping steam Clamp for fixing the Milk Island to the machine LED to show carafe is installed To dismantle, unscrew the screws marked in the illustration 2 2 1 Cappucinatore cover 5 2 Cappucinatore valve cover 4 3 3 Vernay valve 4 Insertion for the Cappucinatore val
CHAPTER 5 SERVICE MODALITY Saeco International Group Rev. 3 / Jan.
TALEA / ODEA - LINE 5.1.1. • 05 SERVICE MODALITY Test mode - Talea Giro and Odea Press the hot water key (steam key on the Odea Go) and turn the appliance on at the same time.
05 SERVICE MODALITY 5.1.2. • TALEA / ODEA - LINE Special function mode - Talea Giro and Odea Press the start key and turn the appliance on at the same time. Keep the start key pressed (clockwise) until all four LEDs flash in the following sequence The following functions are no longer available with those appliances that are installed with the automatic dosing regulation. Rotary knob to set cup capacity Key Function Display Let steam out (approx.
TALEA / ODEA - LINE 5.2.1 05 SERVICE MODALITY Test mode - Talea Ring and Ring Plus Getting started with test mode: • • EXIT 3 • 2 Turn on the appliance. Keep the menu key pressed for approx. 2 seconds until "Cancel" appears in the display. Then press the aroma, steam, menu and hot water keys in that order (1,2,3,4). MENU Navigation: • 1 Function level/display *Test* M0 * Test* M0 (12345) time Ver.00.00.
05 SERVICE MODALITY TALEA / ODEA - LINE Function level/display Key Function Display/description *Test* M3 Test: El.valve/Adjust,Test Dosage quantity/Pump Flowmeter *Test* M3 xx yy z (8) Menu Elctronic valve z: Ev Brew (the electro valve opens) 8: Sensor bean cover (closed) *Test* M3 Setup Aroma (imp) tt Enter: Coffee Adjust: Ring Store: Coffee Dosage quantity start position tt: 60 - 150 dosage quantity start position (From Version 02.00.
TALEA / ODEA - LINE Function level/display *Test* M7 *Test* M7 time LCD backlight xx% *Test* M8 *Test* M8 time *Self test* *Test* M9 *Test* M9 time Exit Saeco International Group 05 SERVICE MODALITY Key Function Display/description Adjustment: LCD backlight Coffee Adjustment (ring) xx: 0 - 100 Autotest • Gearing mechanism test • Grinder test • Cup lift test • Heater and sensor test At the end of the tests, an acoustic signal tells you if the tests were successful or not.
05 SERVICE MODALITY 5.2.2. TALEA / ODEA - LINE Diagnosis menu - Talea Ring and Ring Plus Getting started: • • Keep the menu key pressed for approx. 2 seconds until “Cancel” appears in the display. Then press the menu key, steam key, aroma and hot water key in that order. Menu Address 2. Totalcounters 1. Product counters 1.1 Parameters Total Products N° Comment Total amount of coffee used since production 1.2 Total N° of Espresso N° Total quantity of espresso used since production 1.
TALEA / ODEA - LINE 4. Products Settings 3. Errors Menu Address 05 SERVICE MODALITY Parameters Comment 3.1 Errors List List 3.2 Clear all NO No/Yes 4.1(2,3).1 Product Qty (pulses)165 4.1(2,3).2 4.1 Espresso Settings 4.2 Coffee Settings 4.3. Coffee Settings 4.1(2,3).3 Aroma (1,2,3) 5.1 Prebrewing (1,2) Error memory (20) Reset error memory Stored number of pulses for the cup capacity Aroma setting (1 mild, 2 medium, 3 strong) Prebrewing (0: off, 1: normal, 2: long) 4.1(2,3).
05 SERVICE MODALITY 5. System settings Menu Address 5.12 Grounds Limit 13 5.13 Grounds Left N° TALEA / ODEA - LINE Parameters Comment 5 -25 Dreg stop (number of cycles until the message “Empty dreg drawer” appears 1 - 13 Number of remaining uses until the message “Empty dreg drawer” (counts the uses from 13 downwards) 5.14 Grounds Warning 8 1 - 13 5.15 Cup Warm Power 0 0,1 Page 8 / 17 Rev. 3 / Jan. 2009 If the value in Grounds Left and Grounds Warning are identical, (e. g.
TALEA / ODEA - LINE 5.3.1 05 SERVICE MODALITY Test mode - Talea Touch Getting started with test mode: 3 2 • • Turn on the appliance (wait for hourglass to appear). Within 3 seconds, type in an X in the corner of the display in the sequence shown (beginning at the bottom right). Navigation: 1 4 • • Use the "next" key to move through the menu levels. You can use the three keys on the lower edge of the display to start up to three functions for each menu level. Function group t.
05 SERVICE MODALITY TALEA / ODEA - LINE Function group t.2 - Heater t.2 - heating unit boiler_temp (C°) cup heater next =79.8 Boiler boiler_temp (C°) b Temperature recorded by the temperature sensor. cu heater: cup b boiler: *: * Cup warmer heats up Continuous-flow heater heats up no function * Function group t.3 - Water/steam system t.
TALEA / ODEA - LINE 05 SERVICE MODALITY Function group t.5 - Cup lift t.
05 SERVICE MODALITY TALEA / ODEA - LINE Function group t.8 - Let steam out t.8 - steam out next boiler_temp (C°) start * boiler_temp (C°): current boiler temperature start: *: *: Starts the steam out procedure no function no function * Function group t.8 - Let steam out t.
Counters 1 D1.1.counters Diagnosis menu - Talea Touch 2 Water since filter reset water since last filter reset Errors since production Error since last service Error list (see list) error since last service error log Water since the last cleaning cycle Cleaning cycles carried out Brewing unit n° of cleaning cycles water since last cleaning Number of filters changed = number of filter initialisations water filters since prod. +/- Number of descaling cycles carried out n° of DS.
error product counters Product settings D1.1.2A. e D1.1.3. product counters D1.2.1A Product settings Settings D1.
2 Product settings 1 D1.2.1A Product settings D1.2.
D1.2.2A. System setting D1.2.2B system settings Settings D1. Diagnostics menu (78) cup temperature service date on/off (ON takes over the current date) hot water flowrate +/- (13-18) (18) flowmetre settings (80-100)/(auto dose) (90) Boiler temp. when hot water is dispensed Date setting service Flow rate Grinder pulse with medium +/- (50-150) dose From V..........autodose (automatic setting) +/- (70-120) +/-(130-150) no function temp.inactive (120) Boiler temp.
TALEA / ODEA - LINE 5.4.
CHAPTER 6 STANDARD CONTROLS Saeco International Group up Rev. 3 / Jan.
TALEA / ODEA - LINE 6.1.
06 STANDARD CONTROLS 6.3.
CHAPTER 7 DISASSEMBLY Saeco International Group up Rev. 3 / Jan.
TALEA / ODEA - LINE 7.1. 07 DISASSEMBLY SBS / dispenser To disassemble the SBS Fig.1 • 1 2 Remove the SBS rotary knob. Fig.2 • • Unscrew the fixing screw. Remove the bracket of the SBS rotary knob. Fig.3 • 4 3 7.2. Unscrew the screws shown. Fig.4 • Remove the drain valve. Housing To disassemble the housing - front and upper parts Fig.1 • Remove the cover of the coffee container. • Unscrew the screw marked in the illustration. • Remove the rotary knob from the hot water / steam valve. Fig.
07 DISASSEMBLY TALEA / ODEA - LINE To disassemble the right side part Fig. 1 • 1 Remove the screw shown. Fig. 2 • Remove the screw shown (not with Odea). Fig. 3 2 3 • Remove the screws shown. To disassemble the left side part Fig. 1 • Remove the screws shown. Fig. 2 2 • Fig. 3 • 1 Remove the screws shown. If required, loosen the hose clamp on the hot water / steam valve and remove the hose. 3 1 2 To remove the side panels Fig. 1 • Separate the rear upper side part. Fig.
TALEA / ODEA - LINE 7.3. 07 DISASSEMBLY Electronics To disassemble the control board Fig. 1 • • 1 2 Remove the screws shown. Fold the board to the back. Fig. 2 • Loosen the plug contact. Fig. 3 • Remove the screws shown. 3 To disassemble the power board 1 Fig. 1 • • • 7.4. Remove the black board’s cover. Loosen the plug contact. Remove the screws shown. Boiler’s pin To disassemble the boiler’s pin Fig. 1 • • Remove the screws shown. Remove the water channel cover. Fig.
07 DISASSEMBLY 7.5. TALEA / ODEA - LINE Gear motor device 1 2 To disassemble the gears Fig. 1 • • B Remove the screws shown. Remove the gear cover. Caution: The sensor of the residual water tray is fitted to the gear cover (unplug). Fig. 2 • 3 • If one of the gear wheels is damaged, replace both wheels. If one of the microswitches is defective, always replace both microswitches. Fig. 3 • • Gearing mechanism with 2 microswitches.
TALEA / ODEA - LINE 7.6. 07 DISASSEMBLY Boiler 1 To disassemble the boiler Fig. 1 • 2 1 Remove the screws shown. Fig. 2 1. 2. Remove the screw shown. Release the hook and fold the unit upwards. 2 3 Fig. 3 1. 2. 2 1 4 Fig. 4 • • Saeco International Group Loosen the cable tie. Loosen the boiler from the bracket (Allen key). Rev. 3 / Jan. 2009 Loosen the connections. Replace the boiler.
07 DISASSEMBLY 7.7. TALEA / ODEA - LINE Solenoid valve / multi-way valve 1 To disassemble the solenoid valve / multi-way valve Fig. 1 • • 2 Fig. 2 / 3 • • 2 Remove the screws shown. Loosen the coffee dispenser bracket. Loosen the boiler pin. Loosen the boiler’s bracket (see section 7.6 / Fig. 1 and 2). 3 4 Fig. 4 1. 5 Remove the screw shown. Fig. 5 • Unhinge the pressure-relief hose. Fig. 6 • Remove the valve unit. 6 Page 6 / 13 7 Fig.
TALEA / ODEA - LINE 7.8. 07 DISASSEMBLY Pump 1 To disassemble the pump Fig. 1 • 1 Fig. 2 • 2 Remove the pump and the pump bracket from the guide. Remove the connecting bracket. Fig. 3 • Loosen the hose clamp and remove the hose. 3 Fig. 4 1. Disassembled pump unit. 4 7.9. Hose connections (assembly) 1 Hose connection specifications Fig. 1 • 2 Fig. 2 • Saeco International Group Boiler connection. Rev. 3 / Jan. 2009 Other connections.
07 DISASSEMBLY TALEA / ODEA - LINE To replace the hoses Fig. 1 • To open the clamp, place the pliers at the front. Fig. 2 • Page 8 / 13 Rev. 3 / Jan. 2009 Use pliers to squeeze the clamp.
TALEA / ODEA - LINE 7.10. 07 DISASSEMBLY Coffee grinder 1 To disassemble the coffee grinder Fig. 1 • • A • 2 Fig. 2 1. 3 Loosen the cable tie. Fig. 3 • Saeco International Group Remove the screws shown. Loosen the motor mounting bracket (A). Remove the cover. Rev. 3 / Jan. 2009 When installing, take care that the spring is fitted correctly in the centre of the coffee grinder axis.
07 DISASSEMBLY 7.11. TALEA / ODEA - LINE Grinders To disassemble/adjust the grinding disc Fig. 1 • Press against the grinding level setting axis and then turn the grinding disc support anticlockwise until it stops, then remove it. 1 Fig. 2 1. Turn the grinding disc anticlockwise out of the support. 2 Fig. 3 • Turn the grinding disc anticlockwise out of the support. The bayonet connections can be accessed from the rear side. 3 Fig. 4 1. In the start position, both markings must be aligned.
TALEA / ODEA - LINE 7.12. 07 DISASSEMBLY Adjustment of coffee grinder To adjust the coffee grinder Fig. 1 • A B Insert the centre piece with the flag (A) into the recess (B). 1 Fig. 2 • • • fine Turn clockwise for a coarser setting and anticlockwise for a finer setting. If beans are in the grinder, turn 2 settings finer. Grind and repeat if required. Turn the flag (A) back to the centre. coarse 2 Saeco International Group Rev. 3 / Jan.
07 DISASSEMBLY 7.13. TALEA / ODEA - LINE Cup lift To disassemble the electrical cup lift Fig. 1 • • • Remove the screws shown. Loosen the motor mounting bracket (A). Remove the cover. Fig. 2 1 2 1. Loosen the cable tie. Fig. 3 • When installing, take care that the spring is fitted correctly in the centre of the coffee grinder axis. 3 Page 12 / 13 Rev. 3 / Jan.
TALEA / ODEA - LINE 07 DISASSEMBLY To disassemble the electrical cup lift Fig. 1 • Remove the screws shown. 1 Fig. 2 • • • Remove the securing clips. Loosen the sensor cable. Unhinge the cup lift. 2 Saeco International Group Rev. 3 / Jan.
CHAPTER 8 NOTES Saeco International Group Rev. 3 / Jan.
TALEA / ODEA - LINE Saeco International Group 08 NOTES Rev. 3 / Jan.
08 NOTES Page 2 / 2 TALEA / ODEA - LINE Rev. 3 / Jan.
CHAPTER 9 WATER SYSTEM DIAGRAMS Saeco International Group Rev. 3 / Jan.
Odea Go Flow meter Lined-faced silicone Steam Water tank Steam/water dispensing Silicone tube Silicone tube Boiler 1300 W Pump Lined-faced silicone tube Lined-faced s Pipe fitting of water drain Safety valve 18 - 20 Water draining
tube Hot water/steam faucet Lined-faced silicone tube Coffee dispensing Brewing unit Dispensing valve Boiler‘s pin ilicone tube Pipe fitting of Boiler‘s pin
Odea Giro Plus,Giro Flow meter Lined-faced s Steam L Water tank Steam/water dispensing Silicone tube Silicone tube Pump Boiler 1300 W Lined-faced silicone tube Lined-fac W dra
silicone tube Hot water/steam faucet Lined-faced silicone tube Coffee dispensing Brewing unit Dispensing valve ced silicone tube Boiler‘s pin Dispensing coffee valve 3-5 bar Water aining Safety valve 18 - 20 Pipe fitting of water drain Drain valve
Talea Flow meter Lined-faced silicone tu Steam Lined-face Water tank Steam/water dispensing Silicone tube tube Silicone Silicone tube Pump Boiler 1300 W Lined-faced silicone tube Lined-faced silicon Water draining
Pipe fitting of water drain Hot water/steam faucet ube Water draining Pipe fitting with safety valve 3bar Silicone tube Steam for milk ed silicone tube Lined-faced silicone tube Coffee dispensing Brewing unit SBS valve ne tube Boiler‘s pin Dispensing coffee valve 3-5 bar Pipe fitting of water drain Safety valve 18 - 20 Drain valve
CHAPTER 10 WIRING DIAGRAMS Saeco Internationa Group Rev. 3 / Jan.
Odea Go
Odea Giro
Talea Giro Plus
Talea Ring
Talea Ring plus
Talea Touch Plus
