Technical data

PROGRAMMING THE MACHINE RECOMMENDATIONS
9493
Press the same keys to modify the selected value
(for example to set a new servicing limit).
Through ENT a new value can be saved. On
the contrary, by pressing ESC the new value
entering is stopped and, as a result, the former
counter setting shall be considered.
When the set limit has been reached, the coffee
dispensing stops and the following two messages
are displayed:
"COFFEE DISPENS. "
"BLOCKED "
"SELECT PRODUCT "
"READY FOR USE "
Reset the counters by pressing the cappuccino
selection key
.
Rinsing cycle
This appliance is equipped with a rinsing cycle
program for the usual, daily and weekly rinsing.
If regularly used, this program effectively elimi-
nates the greasiness of coffee in inaccessible
parts and avoids alterations in the taste of
coffee.
Depending on the way the appliance is used, it
is advisable to rinse it every month or after max.
250 cups of coffee. The rinsing cycle lasts about
5 minutes, and it is divided into 4 cycles,
including the rinsing with cold water. Each cycle
is followed by a short pause of about 40
seconds.
Never stop the rinsing cycle.
Important: before starting the rinsing cycle,
always fill completely the water tank and put a
capacious container (min. 1 litre) under the
coffee dispensing unit, which is height-adjust-
able and can be removed for cleaning.
The rinsing cycle needs about 1 litre of water
(including final rinsing). From time to time, empty
the water tank.
By using the keys
move the asterisk to the
menu item
RINSING CYCLE . To enable this
menu item use the ENT key.
The following message appears on the display:
"WASCHING CYCLE "
This function starts the rinsing cycle with water of
those parts concerned with the coffee dispens-
ing. When the rinsing cycle ends, the following
message appears on the display:
"SELECT PRODUCT "
"READY FOR USE "
Dir. water supply
The ROYAL COFFEE BAR is provided with a
connection to the water supply (53).
Connect the machine to a drinking water pipe
having a pressure between 1,5 and 8 bar.
To do this, use a loading tube with adequate
characteristics and connect it to the G3/4”
sleeve placed on the rear part of the frame.
Important:
It is advisable to connect the machine to water
treated with a descaling device, especially in
case of hard water or water high in calcium and
magnesium.
(HARDNESS 4: hard water).
By pressing
move the asterisk to the item
“WATER CONNECTION” and select it by
pressing ENT
The display shows:
"WATER CONNECTION "
"ON "
By pressing the same you can modify the
function “ON or OFF”.
If water connection is on, when leaving the
programming menu the machine displays the
following message:
"EMPTY WATER TANK "
When the water tank is empty and replaced in
its position, the display will show the following
message:
"SELECT PRODUCT "
"READY FOR USE "
From now on the water connection can be used.
If the water supply function is off, the machine will
use the water tank as a stock.
Important: when using the machine for the first
time, passing from the water tank to the water
supply in the programming mode, a DRAINAGE
must be carried out, as described at page 87.
To perform DESCALING you have to set the
following:
"WATER CONNECTION "
"OFF "
For DESCALING see page 100.
Dosage of ground coffee
33
The coffee dosage adjustment lever (18) allows the
selection of the grinding coffee amount from 6 to 9
grams. Place lever (18) on the required position.
RECOMMENDATIONS
Prolonged idleness
If the machine hasn’t been used for a prolonged
period, it is advisable for hygienic reasons to run
a rinse cycle through the machine.
Place a cup under the steam/hot water spout (7)
and fill it with water by operating the hot water
knob.
Preheating cups
Cups may be preheated by placing them on the
special cup heating plate.
Temperature led
When starting the machine, the following
message is displayed:
"WARMING UP...... "
As soon as the operating temperature has been
reached, the following message is displayed:
"SELECT PRODUCT "
"READY FOR USE "
Empty coffee bean container
When coffee beans run out, the coffee grinder
stops and the following message is displayed:
"COF. BEANS EMPTY "
Fill the container and restart the cycle.
Empty water tank
When water runs out, the program stops
automatically and the following message is
displayed:
"WATERTANK EMPTY "
Fill the tank and restart the cycle.
Grounds container warning light
As soon as there are 30 grounds in the container,
the following message is displayed: