ROCKit Bluetooth True Wireless Headset User’s manual
Contents ◼ Brief introduction…………...…………………………..…... 1 ◼ Before use……………………………………………………. 1 1. Overview…………………………………………………...……1 2. Charging for headset..……………………………………………2 2. Charging for charging case.. …………………………………2 ◼ Getting started……..…………………………………………3 1. Wearing headset.............................................................3 2. One earbud connecting with cellphone ......................................3 3. Two earbuds connecting with cellphone..........................................5 4.
Welcome to use this True Wireless Bluetoothheadset, ROCKit. Please read this user’s manual carefully before use. ◼ Brief introduction ROCKit is a Bluetooth True Wireless Headset ,each ear piece comes with a Microphone that can be used individually or used together for stereo sound.The earbudsare equipped with a charging case, which is convenient to carry and charge. The charging case supports wireless charging, and you can charge the charging case with your wireless charger. ◼ Before use 1.
2. Charging for headset When the headset is low on power, thered Ledflashes three times every 1 minute. Please recharge the battery of the headset. The way of charging for the earbuds as following: 1. Put the earbuds into the charging case to ensure that the charging pins connect well, and start charging when you see the red indicator light of the earbuds flashes slowly. Red LED flashes slowly: Charging Red LED off: Finish charging 2. Charging should be completed in roughly 1.5 hours.
Using USB cable 1) Plug the Type-C charging cable into the case’s charging jack. 2) Plug the USB cable into a USB port of PC or a 5Volt USB charge. Wireless charging 1) Connect the wireless charger to the power cable. (some wireless chargers with built-in batteries may not need to be connected to the power cable) 2) Put the charging case in the center of the wireless charger as far as possible for maximum efficiency charging.
◼ Getting started 1. Wearing headset a. Choose the suitable size ear tips b. Ensure each earbuds is worn on the correct ear. “L” should be worn on the left ear and “R”worn on the right ear. Left ear Right ear 2.One earbud connecting with cellphone Each earbuds can be connected singly to the cellphone. 1. Power on 1)When charging, the earbuds will turn on automatically when they are taken out of the charging case.The earbuds emit Four Tone_Low Rising and the white LED light 1 second.
3 3.Connecting To connecting your earbuds to a Bluetooth device, first ensure the device has Bluetooth enable and it is in pairing mode(See your device manual for setting pairing mode) . Once your earbuds are in pairing mode, you should be able to see it in the list of Bluetooth devices. You should see ROCKit-L for left earbuds and ROCKit-R for the right earbuds appear in your contactable devices list. You need to connect one of them to use as master.
Remark: ◆ The earbuds will automatically connect with the latest Bluetooth device when power on again.If the earbuds are not connected, they will enter into pairing mode automatically. ◆ 4 Each earbuds will automatically switch to standby mode if disconnected from device, and will power off automatically after 2 minutes to save power. 3.Two earbuds connecting with cellphone In this mode use two earbuds at the same time to enjoy stereo sound.
5 4.Earbuds pairing/connecting Please use this step if two headset can not be connect with each other. 1.Turn off two earbuds respectively(don’t put them into the charging case). 2.Clear the pairing list: Choose one of the earbuds. Firstly, enter the pairing mode.Then hit the touch button 5 times, while the red light turns on for 1 second. The pairing list will be cleared when emits Four Tone_High Falling after a "dang"prompt. The other headset cleans the pairing list by doing the same. 3.
1. music Function Play Status of earbuds Pausing Playing music Previous Playing song music Playing Next song music Playing Volume up music Volume Playing down music Pause L Prompt tone R Double-click Double-click Dang touch-button touch-button Double-click Double-click Dang touch-button touch-button Press Left touch N/A Dang button about 2s Press Right touch N/A Dang button about 2s N/A Once-click Right Du touch-button Once-click Left N/A Du touch-button 2.
Volume up N/A During a call Once-click touch-button Volume down During a call Once-click touch-button Du N/A Du 6.Function operation----two earbuds connecting with cellphone 1.
Active SIRI Connected device Volume up During a call Volume down During a call Triple-click touch-button N/A Once-click touch-button Triple-click touch-button Once-click touch-button N/A Dang Du Du 3. Gang control to power off When using two earbuds, either earbud of the left or right turns off, and the other earbud will be turned off at the same time.
8. Meaning of indicator light indicator light Earbuds Red and white LED flash quickly alternately Red and white LED flash slowly alternately Red LED flashes every 8.5 seconds White LED flashes once every 9.5 seconds Red LED flashes three times every minute Charging White LED flashes every 2 case seconds White LED flashes three times every two seconds White LED kept on Prompt tone Pairing mode with phone TWS pairing mode Unconnected Connected Low battery Low battery Full battery Has been charged 9.
connection, left earbuds will continue to wait for pairing with the mobile phone (red and white lights flash quickly alternately). ◼ Care and maintenance Read the following recommendations carefully before using BTH109. Following these you will be able to enjoy this product for many years. ◆ Keep it dry and don’t put it in the dump place to avoid the product’s internal circuit being affected. Don’t wear the headset when in strong exercise toavoid sweat enter.
a) Make sure the volume is not too low or muted; b) Make sure the headset connects with the mobile phone correctly; c) Make sure the distance between the headset and the cell phone is in the available Bluetooth range. 4. Why can’t I hear the sound clearly on the headset? a) Make sure the mobile phone is in the strong signal area; b)Make sure the headset is in the available range. and no other block。 5.
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.
