Network Video Recorder Quick Start Guide
Network Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Panels Description .......................................................................................................................6 1.1 Front Panel ........................................................................................................................................... 6 1.1.1 SABVISION NVR32 ..................................................................................................................... 6 1.
Network Video Recorder Quick Start Guide Quick Start Guide About this Manual This Manual is applicable to Network Video Recorder (NVR). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website.
Network Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Video Recorder Quick Start Guide Applicable Models This manual is applicable to the models listed in the following table. Series Models SABVISION NVR16 SABVISION NVR SABVISION NVR32 Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.
Network Video Recorder Quick Start Guide Safety Instructions Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel 1.1.
Network Video Recorder Quick Start Guide Table 1-1 Panel Description No. Name Function Description POWER 1 Status HDD Indicators Tx/Rx Turns green when NVR is powered up. Blinks red when HDD is reading/writing. Blinks green when network connection is functioning normally. The Enter button is used to confirm selection in menu mode; or used to check checkbox fields and ON/OFF switch. In playback mode, it can be used to play or pause the video.
Network Video Recorder Quick Start Guide 1.1.2 SABVISION NVR16 Figure 1-2 SABVISION NVR16 Table 1-2 Panel Description No. Name Connections 1 POWER Turns green when NVR is powered up. 2 HDD Flickers red when data is being read from or written to HDD. 3 Tx/Rx Flickers blue when network connection is functioning properly. 4 USB Interface Universal Serial Bus (USB) port for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 1.2 Rear Panel 1.2.
Network Video Recorder Quick Start Guide 3 LINE IN RCA connector for audio input. 4 HDMI HDMI video output connector. 5 USB 3.0 interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 6 RS-232 Interface Connector for RS-232 devices. 7 VGA DB9 connector for VGA output. Display local video output and menu. 8 RS-485 Interface Half-duplex connector for RS-485 devices. 9 ALARM IN Connector for alarm input.
Network Video Recorder Quick Start Guide 4 HDMI Interface HDMI video output connector. 5 ALARM IN Connector for alarm input. ALARM OUT Connector for alarm output. 6 LAN Interface Network 1 10/100/1000 interface Mbps self-adaptive Ethernet 7 USB Interface Universal Serial Bus (USB 3.0) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up).
Network Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 NVR Installation During installation of the NVR: Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Connect the alarm cable. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. Ensure the NVR is grounded.
Network Video Recorder Quick Start Guide Figure 2-1 Remove Cover Step 2 Connect one end of the data cable to the motherboard of NVR and the other end to the HDD. Figure 2-2 Connect Data Cable Step 3 Connect the power cable to the HDD. Figure 2-3 Connect Power Cable Step 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
Network Video Recorder Quick Start Guide Figure 2-4 Fix Hard Disk 13
Network Video Recorder Quick Start Guide 2.3 Connections 2.3.1 Alarm Input Wiring The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device. Figure 2-5 Alarm Input Wiring 2.3.
Network Video Recorder Quick Start Guide If you connect an AC load to the alarm output 3 of the NVR, then you must remove the JP 3 jumper. 2.3.3 Using Alarm Connectors To connect alarm devices to the NVR: Step 1 Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. Step 2 Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws. Ensure signal cables are tight. Step 3 Connect pluggable block back into terminal block. 2.3.
Network Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 96K 42M 128K 56M 160K 70M 192K 84M 224K 98M 256K 112M 320K 140M 384K 168M 448K 196M 512K 225M 640K 281M 768K 337M 896K 393M 1024K 450M 1280K 562M 1536K 675M 1792K 787M 2048K 900M 4096K 1.8G 8192K 3.6G 16384K 7.
Network Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.
Network Video Recorder Quick Start Guide Step 2 Press the POWER button on the front panel. The Power LED should turn blue. The unit will begin to start. After the device starts up, the wizard will guide you through the initial settings, including modifying password, date and time settings, network settings, HDD initializing, and recording. To shut down the NVR: Step 3 Enter the Shutdown menu. Menu > Shutdown Figure 3-2 Shutdown Step 4 Select the Shutdown button. Step 5 Click the Yes button. 3.
Network Video Recorder Quick Start Guide STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Network Video Recorder Quick Start Guide Connect at least 4 dots to draw the pattern. Each dot can be connected for once only. Step 2 Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully. Step 3 You can use the configured unlock pattern for future login. Figure 3-6 Draw the Unlock Pattern 3.5 Login and Logout 3.5.1 User Login Purpose: If NVR has logged out, you must login the device before operating the menu and other functions.
Network Video Recorder Quick Start Guide In the Login dialog box, if you enter the wrong password 7 times, the current user account will be locked for 60 seconds. 3.5.2 User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to perform any operations, you need to enter user name and password log in again. Step 1 Enter the Shutdown menu. Menu > Shutdown Figure 3-8 Logout Step 2 Click Logout.
Network Video Recorder Quick Start Guide Figure 3-9 Wizard 3.7 Network Settings Purpose: Network settings must be properly configured before you operate NVR over network. Step 1 Enter the Network Settings interface. Menu > Configuration > Network Figure 3-10 Network Settings Step 2 Select the General tab. Step 3 In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server.
Network Video Recorder Quick Start Guide Step 4 If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server. Step 5 After having configured the general settings, click the Apply button to save the settings. 3.8 Adding IP Cameras Purpose: Before you can get live video or record the video files, you should add the network cameras to the connection list of the device.
Network Video Recorder Quick Start Guide Live View Icons In the live view mode, there are icons at the upper-right corner of the screen for each channel, showing the status of the record and alarm in the channel for quick reference. Alarm (video loss, tampering, motion detection, VCA or sensor alarm) Record (manual record, continuous record, motion detection, VCA or alarm triggered record) Alarm and Record Event/Exception (event and exception information, appears at the lower-left corner of the screen.) 3.
Network Video Recorder Quick Start Guide 3.11 Playback The recorded video files on the hard disk can be played back in the following modes: instant playback, all-day playback for the specified channel, and playback by normal/event/smart/tag/sub-periods/external file search. Step 1 Enter playback interface. Click Menu>Playback or from the right-click menu. Step 2 Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar.
Network Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Purpose: You can get access to the device via web browser.
Network Video Recorder Quick Start Guide If the device is already activated, enter the user name and password in the login interface, and click the Login button. Figure 4-2 Login Step 3 Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Video Recorder Quick Start Guide 28
