Raw 700 Manual
Table Of Contents
- page0_DE.PDF
- page1_DE.PDF
- page2_DE.PDF
- page3_DE.PDF
- page4_DE.PDF
- page5_DE.PDF
- page6_DE.PDF
- page7_DE.PDF
- page8_DE.PDF
- page9_DE.PDF
- page10_DE.PDF
- page11_DE.PDF
- page12_DE.PDF
- page13_DE.PDF
- page14_DE.PDF
- page15_DE.PDF
- page16_DE.PDF
- page17_DE.PDF
- page18_DE.PDF
- page19_DE.PDF
- page20_DE.PDF
- page21_DE.PDF
- page22_DE.PDF
- page23_DE.PDF
- page24_DE.PDF
- page25_DE.PDF
- page26_DE.PDF
- page27_DE.PDF
- page28_DE.PDF
- page29_DE.PDF
- page30_DE.PDF
- page31_DE.PDF
- page32_DE.PDF
- page33_DE.PDF
- page34_DE.PDF
- page35_DE.PDF
- page36_DE.PDF
- page37_DE.PDF
- page38_DE.PDF
- page39_DE.PDF
- page40_DE.PDF
- page41_DE.PDF
- page42_DE.PDF
- page43_DE.PDF
- page44_DE.PDF
- page45_DE.PDF
- Sheet1
- Drawing View1
- Drawing View2
- Drawing View4
- Drawing View5
- Drawing View6
- Drawing View8
- Drawing View9
- Drawing View10
- Drawing View11
- Drawing View12
- Drawing View13
- Drawing View14
- Drawing View15
- Drawing View16
- Drawing View17
- Drawing View18
- Drawing View19
- Drawing View20
- Drawing View21
- Drawing View22
- Drawing View23
- Drawing View24
- Drawing View25
- Drawing View26
- Drawing View27
- Drawing View28
- Drawing View29
- Drawing View30
- Drawing View31
- Drawing View32
- Drawing View33
- Drawing View34
- Drawing View35
- Drawing View36
- Drawing View37
- Sheet1
- page46_DE.PDF
- Sheet1
- Drawing View37
- Drawing View38
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View42
- Drawing View45
- Drawing View46
- Drawing View56
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View61
- Drawing View63
- Drawing View65
- Drawing View71
- Drawing View73
- Drawing View75
- Drawing View78
- Drawing View81
- Drawing View82
- Drawing View83
- Drawing View89
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View111
- Drawing View113
- Drawing View115
- Drawing View116
- Sheet1
- page47_DE.PDF
Manual
Extra Card
CANOPY
BOX 4
BOX 1
BOX 3
BOX 2
BLADE HOLDER
*Generic pliers.
*Hexagonal driver, size 1.5, 2, 2.5, 3mm.
*4/5mm T-Wrench.
*5.5mm Socket wrench (for M3 nuts).
*8mm Hex fork wrench (for M5 nuts).
*Medium threadlocker (SAB p/n HA116-S).
*Strong retaining compound (SAB p/n HA115-S).
*Spray lubricant (eg. Try-Flow Oil).
*Synthetic grease (eg. Microlube 261).
*Cyanoacrylate adhesive.
*Pitch Gauge (for set-up).
*Soldering equipment (for motor wiring).
*Electric Motor
*Speed controller
*Batteries: 12S – 4200/5500mAh
*1 flybarless 3 axis control unit
*Radio power system.
*3 cyclic servos
*1 tail rotor servo
*6 channel radio control system on 2.4 GHz
The assembly process is described in the following chapters.
Each chapter provides you with the box, bag and/or foam
numbers you will need for that chapter. The information
is printed in a black box in the upper corner of the page.
INSIDE THE MAIN BOX THERE ARE:
Green screw and Green bearing
in the illustration means you
need to use:
Use retaining compound
( SAB HA115-S )
Use Proper Lubricant
Use CA Glue
Indicates that for this
assembly phase you need
materials that are:
BOX xxx, BAG xxx.
Important
ADDITIONAL COMPONENTS REQUIRED
TOOLS, LUBRICANTS, ADHESIVES
Blue screw and blue bearing
in the illustration means you
need to use:
Thread Locker Medium
Strength
( SAB HA116-S)
Box xx, BAGxx
NOTES FOR ASSEMBLY
Please refer to this manual for assembly instructions for this model. Follow the order of assembly
indicated. The instructions are divided into chapters, which are structured in a way that each step is
based on the work done in the previous step. Changing the order of assembly may result in additional
or unnecessary steps.Use thread lockers and retaining compounds as indicated. In general, each bolt
or screw that engages with a metal part requires thread lock. It is necessary to pay attention to the
symbols listed below:
Page 4
NOTE FOR ASSEMBLY