Kraken 580 Nitro Manual
Table Of Contents
- page0_570KN.PDF
- page1_570KN.PDF
- page2_570KN.PDF
- page3_570KN.PDF
- page4_570KN.PDF
- page5_570KN.PDF
- page6_570KN.PDF
- page7_570KN.PDF
- page8_570KN.PDF
- page9_570KN.PDF
- page10_570KN.PDF
- page11_570KN.PDF
- page12_570KN.PDF
- page13_570KN.PDF
- page14_570KN.PDF
- page15_570KN.PDF
- page16_570KN.PDF
- page17_570KN.PDF
- page18_570KN.PDF
- page19_570KN.PDF
- page20_570KN.PDF
- page21_570KN.PDF
- page22_570KN.PDF
- page23_570KN.PDF
- page24_570KN.PDF
- page25_570KN.PDF
- page26_570KN.PDF
- page27_570KN.PDF
- page28_570KN.PDF
- page29_570KN.PDF
- page30_570KN.PDF
- page31_570KN.PDF
- page32_570KN.PDF
- page33_570KN.PDF
- page34_570KN.PDF
- page35_570KN.PDF
- page36_570KN.PDF
- page37_570KN.PDF
- page38_570KN.PDF
- page39_570KN.PDF
- page40_570KN.PDF
- page41_570KN.PDF
- page42_570KN.PDF
- page43_570KN.PDF
- page44_570KN.PDF
- Sheet1
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View57
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View65
- Drawing View66
- Drawing View67
- Drawing View69
- Drawing View70
- Drawing View71
- Drawing View72
- Drawing View73
- Drawing View74
- Drawing View75
- Drawing View76
- Drawing View77
- Drawing View78
- Drawing View79
- Drawing View80
- Drawing View81
- Sheet1
- page45_570KN.PDF
- Sheet1
- Drawing View15
- Drawing View19
- Drawing View20
- Drawing View22
- Drawing View24
- Drawing View29
- Drawing View31
- Drawing View32
- Drawing View37
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View44
- Drawing View45
- Drawing View48
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View56
- Drawing View57
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View61
- Drawing View62
- Sheet1
- page46_570KN.PDF
- Sheet1
- Drawing View56
- Drawing View59
- Drawing View78
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View112
- Drawing View122
- Drawing View124
- Drawing View125
- Drawing View127
- Drawing View128
- Drawing View130
- Drawing View131
- Drawing View133
- Drawing View134
- Drawing View135
- Drawing View136
- Drawing View138
- Drawing View142
- Drawing View144
- Sheet1
- page47_570KN.PDF
CUT
BAG2.4
The second is to use two magnets on the fan. Please use the following methods for installation:
Install 2 magnets on the fan with epoxy glue
(please ensure to clean the parts with degreaser before glueing together)
[ Fig. 1 ] ). To install the sensor, you can use the two pre-cut M2.5 holes.
Not all sensors are the same, so you can adapt the position with the carbon support (H0729).
With Align and Spartan sensors, you can use the part of the support that already has holes in it.
With any other sensor, you can use the part without holes and adapt as required.
INSTALLATION OF THE RPM SENSOR
On the 580 nitro it is possible to use two different methods to install an RPM sensor.
The first is a backplate sensor as demonstrated in the picture on the right.
P.S:
Not all YS engines can support this method. Please seek further guidance from your engine
manufacturer.
Magnet
Sensor
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
H0729-S RPM Sensor Support
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
RPM Sensor
Support
Sensor
ENGINE
ASSEMBLY
Page 8
ENGINE UNIT ASSEMBLY