Kraken 580 Nitro Manual
Table Of Contents
- page0_570KN.PDF
- page1_570KN.PDF
- page2_570KN.PDF
- page3_570KN.PDF
- page4_570KN.PDF
- page5_570KN.PDF
- page6_570KN.PDF
- page7_570KN.PDF
- page8_570KN.PDF
- page9_570KN.PDF
- page10_570KN.PDF
- page11_570KN.PDF
- page12_570KN.PDF
- page13_570KN.PDF
- page14_570KN.PDF
- page15_570KN.PDF
- page16_570KN.PDF
- page17_570KN.PDF
- page18_570KN.PDF
- page19_570KN.PDF
- page20_570KN.PDF
- page21_570KN.PDF
- page22_570KN.PDF
- page23_570KN.PDF
- page24_570KN.PDF
- page25_570KN.PDF
- page26_570KN.PDF
- page27_570KN.PDF
- page28_570KN.PDF
- page29_570KN.PDF
- page30_570KN.PDF
- page31_570KN.PDF
- page32_570KN.PDF
- page33_570KN.PDF
- page34_570KN.PDF
- page35_570KN.PDF
- page36_570KN.PDF
- page37_570KN.PDF
- page38_570KN.PDF
- page39_570KN.PDF
- page40_570KN.PDF
- page41_570KN.PDF
- page42_570KN.PDF
- page43_570KN.PDF
- page44_570KN.PDF
- Sheet1
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View57
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View65
- Drawing View66
- Drawing View67
- Drawing View69
- Drawing View70
- Drawing View71
- Drawing View72
- Drawing View73
- Drawing View74
- Drawing View75
- Drawing View76
- Drawing View77
- Drawing View78
- Drawing View79
- Drawing View80
- Drawing View81
- Sheet1
- page45_570KN.PDF
- Sheet1
- Drawing View15
- Drawing View19
- Drawing View20
- Drawing View22
- Drawing View24
- Drawing View29
- Drawing View31
- Drawing View32
- Drawing View37
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View44
- Drawing View45
- Drawing View48
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View56
- Drawing View57
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View61
- Drawing View62
- Sheet1
- page46_570KN.PDF
- Sheet1
- Drawing View56
- Drawing View59
- Drawing View78
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View112
- Drawing View122
- Drawing View124
- Drawing View125
- Drawing View127
- Drawing View128
- Drawing View130
- Drawing View131
- Drawing View133
- Drawing View134
- Drawing View135
- Drawing View136
- Drawing View138
- Drawing View142
- Drawing View144
- Sheet1
- page47_570KN.PDF
Canopy
Boom
Foam Box
Bag Box
Blade Holder
Blades, Tail Blades,
Carbon Rod
Landing Gear Bag
Tank
Fan Case
Main
Frame
Manual
Product Card
Extra Card
*Generic pliers.
*Hexagonal driver, size 1.5, 2, 2.5, 3mm.
*4/5mm T-Wrench.
*5.5mm Socket wrench (for M3 nuts).
*8mm Hex fork wrench (for M5 nuts).
*Medium threadlocker (SAB p/n HA116-S).
*Strong retaining compound (SAB p/n HA115-S).
*Spray lubricant (eg. Tri-Flow Oil).
*Synthetic grease (eg. Microlube 261).
*Cyanoacrylate adhesive.
*Pitch Gauge (for set-up).
*Soldering equipment (for motor wiring).
*Engine: .50 to .60 Nitro Heli Engine.
*Muffer suited for the engine being used.
*Batteries: 2S/1600-3000mAh.
*Governor unit.
*1 flybarless 3 axis control unit
*Radio power system.
*1 throttle servo ( Mini Size ).
*3 cyclic servos ( Mini Size ).
*1 tail rotor servo ( Standard Size ).
*6 channel radio control system on 2.4 GHz
*Fuel.
The assembly process is described in the following chapters.
Each chapter provides you with the box, bag and/or foam
numbers you will need for that chapter. The information
is printed in a black box in the upper corner of the page.
INSIDE THE MAIN BOX THERE ARE:
Green screw and Green bearing
in the illustration means you
need to use:
Use retaining compound
( SAB HA115-S )
Use Proper Lubricant
Use CA Glue
Indicates that for this
assembly phase you need
materials that are:
Foam xxx, BAG xxx.
Important
ADDITIONAL COMPONENTS REQUIRED
TOOLS, LUBRICANTS, ADHESIVES
Blue screw and blue bearing
in the illustration means you
need to use:
Thread Locker Medium
Strength
( SAB HA116-S)
Foam xx, BAGxx
NOTES FOR ASSEMBLY
Please refer to this manual for assembly instructions for this model. Follow the order of assembly
indicated. The instructions are divided into chapters, which are structured in a way that each step is
based on the work done in the previous step. Changing the order of assembly may result in additional
or unnecessary steps.Use thread lockers and retaining compounds as indicated. In general, each bolt
or screw that engages with a metal part requires thread lock. It is necessary to pay attention to the
symbols listed below:
Page 4
NOTE FOR ASSEMBLY