Kraken 580 Nitro Manual
Table Of Contents
- page0_570KN.PDF
- page1_570KN.PDF
- page2_570KN.PDF
- page3_570KN.PDF
- page4_570KN.PDF
- page5_570KN.PDF
- page6_570KN.PDF
- page7_570KN.PDF
- page8_570KN.PDF
- page9_570KN.PDF
- page10_570KN.PDF
- page11_570KN.PDF
- page12_570KN.PDF
- page13_570KN.PDF
- page14_570KN.PDF
- page15_570KN.PDF
- page16_570KN.PDF
- page17_570KN.PDF
- page18_570KN.PDF
- page19_570KN.PDF
- page20_570KN.PDF
- page21_570KN.PDF
- page22_570KN.PDF
- page23_570KN.PDF
- page24_570KN.PDF
- page25_570KN.PDF
- page26_570KN.PDF
- page27_570KN.PDF
- page28_570KN.PDF
- page29_570KN.PDF
- page30_570KN.PDF
- page31_570KN.PDF
- page32_570KN.PDF
- page33_570KN.PDF
- page34_570KN.PDF
- page35_570KN.PDF
- page36_570KN.PDF
- page37_570KN.PDF
- page38_570KN.PDF
- page39_570KN.PDF
- page40_570KN.PDF
- page41_570KN.PDF
- page42_570KN.PDF
- page43_570KN.PDF
- page44_570KN.PDF
- Sheet1
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View57
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View65
- Drawing View66
- Drawing View67
- Drawing View69
- Drawing View70
- Drawing View71
- Drawing View72
- Drawing View73
- Drawing View74
- Drawing View75
- Drawing View76
- Drawing View77
- Drawing View78
- Drawing View79
- Drawing View80
- Drawing View81
- Sheet1
- page45_570KN.PDF
- Sheet1
- Drawing View15
- Drawing View19
- Drawing View20
- Drawing View22
- Drawing View24
- Drawing View29
- Drawing View31
- Drawing View32
- Drawing View37
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View44
- Drawing View45
- Drawing View48
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View56
- Drawing View57
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View61
- Drawing View62
- Sheet1
- page46_570KN.PDF
- Sheet1
- Drawing View56
- Drawing View59
- Drawing View78
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View112
- Drawing View122
- Drawing View124
- Drawing View125
- Drawing View127
- Drawing View128
- Drawing View130
- Drawing View131
- Drawing View133
- Drawing View134
- Drawing View135
- Drawing View136
- Drawing View138
- Drawing View142
- Drawing View144
- Sheet1
- page47_570KN.PDF
90°
17-18mm
Small Servo Tool
SERVO ASSEMBLY
Mini Servo
Servo Arm
(HA050-S)
Socket screw M3x6mm
(HC044-S)
Uniball M2
(H0064-S)
The linkage ball must be positioned 17-18 mm out on the servo arm. The recommended servo arm
to use is: SAB p/n [HA050/HA051].
Ensure the alignment of the servo arms (and sub trim set) before installing the servos in the model.
Proceed with installation following the instructions below. You can use the G10 servo tool to align
the front servo arms with the theoretical horizontal line.
(Figure 3)
Socket head cap
screw M2.5x8mm
(HC020-S)
Socket head cap
screw M2.5x8mm
(HC020-S)
Socket head cap
screw M2.5x8mm
(HC020-S)
Servo spacer
(H1223-S)
Servo spacer
(H1223-S)
Front Servos
Rear Servo
BAG8
Socket screw M2x6mm
(HC004-S)
NOTE:
Suggested servo wire routing.
Page 16
SWASHPLATE SERVOS ASSEMBLY