Kraken 580 Manual

[HC437-S] [HC430-S]
[HC586-S]
- 1 x Motor Belt GT3-282-19 mm .
- 1 x Carbon Rod
2.5x 4x570.
- 2 x Plastic Ball Linkage.
- 2 x Thread Rod M2.5x40.
- 2 x Aluminum Bush.
- 2 x Rad Bearing 30x 37x4.
- 2 x Thrust Bearing 10x 14x4.
[HA021-S] [HA035-S]
[HA041-S] [HA078-S]
- 2 x Canopy Grommet . - 2 x Double side tape 30x100x1 .
- 2 x Strap 20x250mm . - 4 x Futaba servo arm.
[HA075-S] [HA076-S]
- 1 x Free Wheel Clutches grease. - 1 x Tranmissions module grease.
- 2 x Ball Bearing 8x 14x4.
[HC417-S]
- 4 x Ball Bearing 10x 15x4.
[HC420-S]
[HC434-S]
- 2 x Thrust Bearing
4x 9x4.
- 2 x Main Blades 570 White. - 2 x Tail Blades 95 White.
TAIL BLADES 95 WHITE
(BW5095)
MAIN BLADES 570 WHITE
(BW0570)
[HC544-S]
- 8 x Head Cap Screw M4x20mm .
[HC549-S]
- 8 x Tapping Screw M3x12mm .
[HC592-S]
- 1 x Tail Belt 1722mm HTD3 .
[HC582-S]
- 8 x Head Screw Special M4x8 .
[HC587-S]
- 1 x Ball Bearing Ø10xØ24x7mm.
- 1 x Ball Bearing 10 x 22 x 6 mm.
- 1 x Ball Bearing 2RSØ10xØ22x6.
- 1 x Ball Bearing Ø6xØ13x5mm.
- 1 x Wave Washer Ø10xØ15x0.3.
- 2 x Pin 3x6mm.
- 1 x Head Cap Shoulder M4x30.
- 1 x Bushing.
- 1 x Shim Ø6xØ9x0.2mm.
[HC588-S]
[HC594-S]
[HA050-S] [HA051-S]
- 2 x Spacer Ø7xØ9x0,5mm.
- 2 x Grip Link Bushing.
- 2 x Spacer Ø4xØ6,9x0,5mm.
- 2 x Spacer Ø8xØ12,5x0,5mm.
- 2 x Spacer Ø11xØ13,8x0,5mm.
- 2 x Spacer Arm Ø2,5xØ4x6,3mm.
- 2 x Oring 90
.
- 2 x Spacer Arm Ø2,5xØ4x3mm.
- 2 x Washer Ø2,5xØ4x0,3mm.
- 2 x Washer Ø4.1xØ6x0.1mm.
- 2 x Spring Washer Ø10xØ15x0.3mm.
- 2 x Washer Ø8xØ14x0.2mm.
- 4 x JR servo arm. - 1 x Foam Blade Holder 580.
Page 46
SPARE PARTS