Kraken 580 Manual
Table Of Contents
- 580-KRAKEN6-front.jpg
- page1_570K.PDF
- page2_570K.PDF
- page3_570K.PDF
- page4_570K.PDF
- page5_570K.PDF
- page6_570K.PDF
- page7_570K.PDF
- page8_570K.PDF
- page9_570K.PDF
- page10_570K.PDF
- page11_570K.PDF
- page12_570K.PDF
- page13_570K.PDF
- page14_570K.PDF
- page15_570K.PDF
- page16_570K.PDF
- page17_570K.PDF
- page18_570K.PDF
- page19_570K.PDF
- page20_570K.PDF
- page21_570K.PDF
- page22_570K.PDF
- page23_570K.PDF
- page24_570K.PDF
- page25_570K.PDF
- page26_570K.PDF
- page27_570K.PDF
- page28_570K.PDF
- page29_570K.PDF
- page30_570K.PDF
- page31_570K.PDF
- page32_570K.PDF
- page33_570K.PDF
- page34_570K.PDF
- page35_570K.PDF
- page36_570K.PDF
- page37_570K.PDF
- page38_570K.PDF
- page39_570K.PDF
- page40_570K.PDF
- page41_570K.PDF
- page42_570K.PDF
- page43_570K.PDF
- page44_570K.PDF
- page45_570K.PDF
- Sheet1
- Drawing View15
- Drawing View18
- Drawing View19
- Drawing View20
- Drawing View22
- Drawing View24
- Drawing View29
- Drawing View30
- Drawing View31
- Drawing View32
- Drawing View37
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View43
- Drawing View44
- Drawing View45
- Drawing View48
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View57
- Sheet1
- page46_570K.PDF
- Sheet1
- Drawing View56
- Drawing View59
- Drawing View78
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View112
- Drawing View122
- Drawing View124
- Drawing View125
- Drawing View127
- Drawing View128
- Drawing View130
- Drawing View131
- Drawing View133
- Drawing View134
- Drawing View135
- Drawing View136
- Drawing View138
- Drawing View142
- Sheet1
Ball Bearing
10x
22x6mm
(HC587-S)
Ball Bearing 2Rs
10x
22x6mm
(HC587-S)
1
2
3
MAIN SHAFT REPLACEMENT
For replacing the main shaft:
*Remove the serial number plate
*Remove the
M4
screw
*Remove and replace the main shaft
*Screw in the
M4
screw, with high force and using green loctite
Main Top
Structure
(H1205-S)
Main Shaft
(H1299-S)
K Gear Z14 0.75
(H1209-S)
K Gear Z58 0.75
(H1208-S)
Main Structure
(H1211-S)
Serial Number
(H1212-S)
TRANSMISSION MODULE
The transmission module is supplied assembled and verified, ready to be used.
Use SAB HA076
Grease inside the module.
Before you open the transmission
module, use heat to neutralize the
loctite. (example use a gas torch)
NOTE:
Before opening the transmission module,
use heat to break down the loctite.
(example: use a gas torch)
NOTE:
[HC128]
Wave Washer
(HC587-S)
M4x30
(HC587-S)
Pin 3x6
Bushing
(HC587-S)
Ball Bearing 2Rs
10x
24x7mm
(HC587-S)
Ball Bearing
6x
13x5mm
(HC587-S)
Bushing
(HC587-S)
Shim
(HC587-S)
Socket Head Cap Screw M3x10mm
(HC056-S)
HC232
Page 40
TRANSMISSION MODULE