Kraken 580 Manual
Table Of Contents
- 580-KRAKEN6-front.jpg
- page1_570K.PDF
- page2_570K.PDF
- page3_570K.PDF
- page4_570K.PDF
- page5_570K.PDF
- page6_570K.PDF
- page7_570K.PDF
- page8_570K.PDF
- page9_570K.PDF
- page10_570K.PDF
- page11_570K.PDF
- page12_570K.PDF
- page13_570K.PDF
- page14_570K.PDF
- page15_570K.PDF
- page16_570K.PDF
- page17_570K.PDF
- page18_570K.PDF
- page19_570K.PDF
- page20_570K.PDF
- page21_570K.PDF
- page22_570K.PDF
- page23_570K.PDF
- page24_570K.PDF
- page25_570K.PDF
- page26_570K.PDF
- page27_570K.PDF
- page28_570K.PDF
- page29_570K.PDF
- page30_570K.PDF
- page31_570K.PDF
- page32_570K.PDF
- page33_570K.PDF
- page34_570K.PDF
- page35_570K.PDF
- page36_570K.PDF
- page37_570K.PDF
- page38_570K.PDF
- page39_570K.PDF
- page40_570K.PDF
- page41_570K.PDF
- page42_570K.PDF
- page43_570K.PDF
- page44_570K.PDF
- page45_570K.PDF
- Sheet1
- Drawing View15
- Drawing View18
- Drawing View19
- Drawing View20
- Drawing View22
- Drawing View24
- Drawing View29
- Drawing View30
- Drawing View31
- Drawing View32
- Drawing View37
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View43
- Drawing View44
- Drawing View45
- Drawing View48
- Drawing View51
- Drawing View52
- Drawing View53
- Drawing View54
- Drawing View55
- Drawing View56
- Drawing View57
- Sheet1
- page46_570K.PDF
- Sheet1
- Drawing View56
- Drawing View59
- Drawing View78
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View112
- Drawing View122
- Drawing View124
- Drawing View125
- Drawing View127
- Drawing View128
- Drawing View130
- Drawing View131
- Drawing View133
- Drawing View134
- Drawing View135
- Drawing View136
- Drawing View138
- Drawing View142
- Sheet1
Note: Larger ID
Note: Smaller ID
Button Head Cap
Screw M6x10mm
(HC122-S)
Washer
6x
12 x1mm
(HC193-S)
Bearing
8x
14x4mm
(HC417-S)
Thrust Bearing
8x
14x4mm
(HC437-S)
Washer
11x
13.8x0.5mm
(HC594-S)
Socket Head Cap Screw M2.5x15mm
(HC028-S)
Washer
2.5x
4x0.3mm
(HC172-S)
Socket Head Cap
Screw M2.5x18mm
(HC032-S)
Blade Grip Arm
(H1202-S)
Uniball M3
(H0065-S)
Socket Head Cap
Screw Special M4x8mm
(HC582-S)
Blade Grip
(H1201-S)
NOTE:
Washer
8x
14x0.2mm [HC228-S]
After approximately 10/20 flights, please check preload, you can
add one 0.2mm shim (HC232) on each side if preload has changed.
However, we suggest to replace the o-rings after about 100 flights.
eg: Microlube
GL261
Foam 2, BAG7
LINKAGE ROD
ASSEMBLED
RADIUS ARM
ASSEMBLED
UNIBALL RADIUS ARM
ASSEMBLED
Washer
8x
14x0.2mm
[HC228-S]
It is a normal ( especially with the 90° + 90° O-ring set-up ) to feel tight after initial assembly
as the axial preload is usually high when the helicopter is brand new.
The preload will loosen up after 5-10 flights allowing the system to become smooth.
Page 12
HEAD ASSEMBLY