User's Manual

■ Listening to the playback sounds of
portable audio player, etc.
Headphone (not
supplied)
3RUWDEOHDXGLR
SOD\HUHWF
$XGLRFDEOHQRWVXSSOLHG
18VHDFRQQHFWLRQFRUGWRFRQQHFWWKHSRUWDEOHDXGLRSOD\HUHWF
WRWKH$8',2,1MDFN:KHQXVLQJYLGHRHTXLSPHQWFRQQHFWWKH
audio output to this unit and the video output to a television.
23UHVVWKH2167$1'%<EXWWRQWRWXUQWKHSRZHURQ
33UHVV WKH$8',2 ,1 EXWWRQ RQ WKH UHPRWH FRQWURO RU781(5
$8',2,1EXWWRQUHSHDWHGO\RQ WKHPDLQXQLWWRVHOHFW$8',2
IN function.
4 Play the connected equipment. If volume level of the connected
GHYLFH LV WRR KLJK VRXQG GLVWRUWLRQ PD\ RFFXU 6KRXOG WKLV
KDSSHQ ORZHU WKH YROXPH RIWKH FRQQHFWHG GHYLFH ,I YROXPH
OHYHOLVWRRORZLQFUHDVHWKHYROXPHRIWKHFRQQHFWHGGHYLFH
Note:
7R SUHYHQW QRLVH LQWHUIHUHQFH SODFH WKH XQLW DZD\ IURP WKH
television.
■ Headphones
z Do not turn the volume on to full at switch on and listen to music
at moderate levels. Excessive sound pressure from earphones
and headphones can cause hearing loss.
z %HIRUH SOXJJLQJ LQ RU XQSOXJJLQJ WKH KHDGSKRQH UHGXFH WKH
volume.
z Be sure your headphone has a 3.5 mm (1/8”) diameter plug
DQGLPSHGDQFHEHWZHHQDQGRKPV7KHUHFRPPHQGHG
impedance is 32 ohms.
z Plugging in the headphone disconnects the speakers
DXWRPDWLFDOO\$GMXVWWKHYROXPHXVLQJWKH92/80(FRQWURO
Connecting other equipment (continued)
0DQ\ SRWHQWLDO SUREOHPV FDQ EH UHVROYHG E\ WKH RZQHU ZLWKRXW
calling a service technician.
,IVRPHWKLQJLVZURQJZLWKWKLVSURGXFWFKHFNWKHIROORZLQJEHIRUH
calling your authorised SHARP dealer or service center.
■ General
Symptom Possible cause
z:KHQDEXWWRQLV
SUHVVHGWKHXQLW
does not respond.
z Set the unit to the power
VWDQGE\PRGHDQGWKHQ
WXUQLWEDFNRQ
z,IWKHXQLWVWLOOPDOIXQFWLRQV
reset it. (Refer “Factory
UHVHWFOHDULQJDOO
memory”.)
z No sound is heard. z The volume level is set to
“MIN”.
z The headphones are
connected.
z Sound too low or
distorted.
z Power suddenly
shuts down.
z7KHEDWWHULHVDUHGHSOHWHG
&KDQJHWKHEDWWHULHV
■ Remote control
Symptom Possible cause
z The remote control
does not operate.
z The AC power cord of the
unit is not plugged in.
z:URQJEDWWHU\SRODULW\
z7KHEDWWHULHVDUH
exhausted.
z The distance or angle is
incorrect.
z The remote control sensor
receives strong light or
sunlight.
■ NFC / Bluetooth
Symptom Possible cause
● No sound is heard. ● The unit is too far from the
Bluetooth stereo audio
source device.
● The unit is not paired
with the Bluetooth stereo
audio source device.
● Bluetooth sound
is interrupted or
distorted.
● The unit is too near to
a device that generates
electromagnetic radiation.
● There is an obstacle
between the unit and the
Bluetooth stereo audio
source device.
● NFC-enabled device
cannot connect to
Bluetooth via NFC tag.
● Main unit is not in
Bluetooth pairing mode.
Perform “NFC connection
for audio playback”.
(Refer page 11.)
Troubleshooting chart
E-20