Installation Guide

CorruBracket
™
Install
888-825-3432 | www.S-5.com
The right way to attach almost anything to metal roofs!
S-5!® Warning! Please use this product responsibly!
S-5!® Warning! Please use this product responsibly! Products are protected by multiple U.S. and foreign patents. For published data regarding holding strength, fastener torque, patents, and trademarks,
visit the S-5! website at www.S-5.com.
Copyright 2013, Metal Roof Innovations, Ltd. S-5! products are patent protected.
S-5! aggressively protects its patents, trademarks, and copyrights. Version 072413.
These instructions are for use by those experienced in the trade. Always follow appropriate safety precautions and use appropriate tools.
Installation Instructions
S-5!® Warning! Please use these products responsibly! Visit our website or
contact your S-5! distributor for available load test results. The user and/or
installer of these parts is responsible for all necessary engineering and design
to ensure the CorruBracket™ has been properly spaced and configured.
Notice to S-5! users: Due to the many variables involved with specific panel
products, climates, snow melt phenomena, and job particulars, the
manufacturer cannot and does not express any opinions as to the suitability
of any S-5! assembly for any specific application and assumes no liability with
respect thereto. S-5! products are tested for ultimate holding strength on
various profile types and materials. This information is available from the S-5!
website: www.S-5.com. This document is an installation guide only and the
photographs and drawings herein are for the purpose of illustrating
installation, tools and techniques, not system designs. Information
contained within is intended to apply to the document as a whole.
The CorruBracket is made for corrugated roofing profiles. It is not made
for folded seams and does not use setscrews. Screws used to secure the
CorruBracket to roof and substrate will vary based upon specific project
requirements and are not supplied by S-5!. For more information see
proper hardware below and please consult your S-5! distributor.
Tools Needed
• Screw Gun (for time saving tool recommendations contact S-5!)
• Rag
• String Line
CorruBracket must be mounted directly over and into the supporting structure
of the roof, i.e. wood decking, wood or steel purlins or trusses, NEVER into the
metal roofing material alone.
To ensure brackets are installed in a straight line, install a single CorruBracket™ on
each end of the roof at a measured, consistent distance from the bottom edge of
the roof. Use a string line between the two brackets. Mount the remaining
CorruBracket along the string line, directly into the supporting structure of the roof.
To Install CorruBracket
™
1. Determine the location of the supporting structure of the roof. When possible, secure the CorruBracket using all hole
locations; when not possible, always use the two upslope hole locations. The only surface preparation necessary is to
simply wipe away excess oil and debris.
2. Peel the release paper from both bases, align, and apply to the clean area.
3.
Secure the CorruBracket by drilling appropriate screws into the pre-punched holes and directly into the supporting
structure of the roof. The CorruBracket is now ready to install ancillaries by using an M8 bolt. For critical attachment
applications utilizing an M8-1.25 x 16 mm Hex Flange Bolt, tighten the M8 bolt to 160 inch pounds (13 foot pounds)
.
R
1
2
3
Only use appropriate screws, and hardware when attaching this product
into the supporting structure.
Use Proper Hardware
Metal to Metal Screw Specifications: 1/4-14 Self
Drilling Screw - 1-1/2" to 2-1/2" Length - 3/8" Hex
Washer Head - Zinc/Aluminum Cap
Metal to Wood Screw Specifications: 1/4-14 Type 17-
AB Milled Point - 1-1/2" to 2-1/2" Length - 3/8" Hex
Washer Head - Zinc/Aluminum Cap
Not Provided
Not Provided
CBI-V1.0-0915