Datasheet

wwxt*frmg #SmffiitrffiKffi,
msm*erfia$s S*st
A- outside legs
l/zu
13/q' 29' 12
B- inside legs
Vq'
13/q' 29'
C top and bottom
rAIIS
Tt' 5"
D
panels
1/zu
14' 171/q'
0P
E- edging
1/qu 1/2,
171/4" 0
F. spacers
1/2, 1/2,
4r/q' 0 12
G sides /q' 23' 245/a' 0P
H top
and bottom
/q' 23' 147/a'
0P
l. side edging
1/q, 3/tu
24s/a' 0
the top edges and ends, where shown.
QPosition
the crest on the top, where
tJshown.
Drill
pilot
and countersunk
shank holes through the top into
the crest,
and drive
in
the screws.
Note: We
found
it easiest to
stain
the top
assembly
(W/X)
before attaching it.
/l
Screw the
large
end of the desktop
-f
fasteners to the top rails
(C)
with
#8x1" flathead
wood screws.
Center
the
top assembly
(WX)
on the desk, and
drive
the #8xls" flathead
wood screws
through the small end of the fasteners
into the bottom side
of the top.
1/q, 3/q,
147/a' 0
K
back
1/c,
155/a" 237/a'
0P
L
dividers
Vq'
11/z' 147/s'
0
M
cap
Tq'
11/q' 28'
N
crossrails
l/zu
25/a' 28'
O cleats
3/q, 3/q'
25/a' 0
P'front and back
1/zu
103/q, 133/a" E0
Q*
sides
1/zu
103/t' 21'
E0
R fronts and backs
l/zu
51/4'
13s/e' 0
S sides
1/z'
51/q' 21'
T
bottoms
1/qu
13%" 201/z'
0P
U-
face
3/q'
109/t' 14lq' E0
V faces
3/qu
51/q' 143/c', 0
W- top
3/q'
26'
517e"
E0
X crest
3/qu
3"
49s/a'
0
-Parts
initially
cut oversize. See the instructions,
ldat*riaii {ey
O-oak, OP-oak
plywood,
E0-edge-joined
oak.
$uirpli*sr
#8x%",
#8x1
,
#8x1t/2",
and #8x2" flathead
wood screws;
#8x1"
panhead
screws; white
glue;
easy-
release
painters'
tape.
ilia**l
;:ntl
iliis; Dado
blade, chamfer bit, %" Forstner
bit,
flush-trim bit,
%"
round-over
bit,
t/s"
round-over bit.
Suying Swide
l"'inrciiiar*.
Desktop fasteners, no. KV'1547
(6);
1/+"-
diam. solid-brass
knobs with
satin chrome
finish,
no. A01950 G10
(3)
with
#8-32x1
t/2"
machine screws;
20
full-extension
slides,
no. KV8400 B20
(3
pr.)
with
screws, 0rder
kit no.
KlTl
102,
$49,95
ppd.,
from
Woodworke/s Hardware.
Call 800/383-0130 or oo
to
www.wwhardware.com.
Photographs: Mafi Baldwin
WOOD magazine November 2002
J-
top
and bottom
e0grng
$-
S
@
3/ax71/q
x 96" Oak
(2
needed)
Drawing
2, and drive the screws into the
face. Drill a hole for the knob
screw,
where
shown.
Repeat for
the
remaining
drawers.
Note: We
found
it easiest
to stain the
drawerfaces
(U,
V) before installing them.
Top
it off
I
Edge-join
enough
3/q"
-thick
stock
I
for
the top
(W),
and cut to size.
Rout a
/+"
round-over
on the top edges
and a
1/8"
round-over on the bottom
edges, where shown on Drawing
3.
)Cut
the crest
(X)
to size. Mark
the
Harch
on the crest, where
shown.
(Use
the technique
that
you
used to
mark
the arch on the bottom rails.
Written by Owen Duvall
94
except
you'll
need
a 54"Jong
fairing
finish up
strip.) Using a compass. mark the 2%"
I
Finish-sand
any
pafls
not
previous-
tFinally.
apply lwo coats of a clear
radius in the center of the crest. where I ly sanded to 220
grir.
Remove
the
Crfinish
on all stained areas. sanding
dimensioned,
Bandsaw
the top of the dust. Then, apply stain to these
parts
between coats.
(We
brushed on
crest to shape, and
sand to remove saw and to the unfinished surfaces of the
polyurethane.)
Then, install the drawer
marks. Now, rovt
t/+"
round-overs along side-panel
assemblies.
knobs with 1Vz" machine screws.
i
3/q
x
51/z x 96" Oak
1/z
x 48 x 48"
Oak
plywood
t/q
x 3t/z x 96" Oak
3/qx51/2x96"
3/q
x 48 x 48"
Oak
plywood
s/q
x71/q x
96"
*Plane
or resaw to the thickness listed in the Materials List.
1/q
x 48 x 48"
Oak
plywood
Prolect
design: Kevin Boyle lllustrations: Roxanne LeMoine; Lorna
Johnson