OPERATOR’S MANUAL Expand-it™ Edger Attachment UT15518F Your Expand-it™ Edger Attachment has been engineered and manufactured to a high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying an Expand-it™ Product.
TABLE OF CONTENTS Introduction ................................................................................................................................................................... 2 General Safety Rules .................................................................................................................................................... 3 Specific Safety Rules ..............................................................................................................
GENERAL SAFETY RULES Inspect unit before each use for loose fasteners and damaged or missing parts. Correct before using the attachment. Failure to do so can cause serious injury. WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury. Use only identical manufacturer’s replacement parts and accessories. Use of any other parts may create a hazard or cause product damage.
SPECIFIC SAFETY RULES Clear the work area before each use. Remove all objects such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the edger blade. wire rope which can break off and become a dangerous projectile). Always push the edger attachment slowly over rough ground.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Safety Alert Symbol Precautions that involve your safety. Read The Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Eye and Hearing Protection Wear eye and hearing protection when operating this equipment.
FEATURES PRODUCT SPECIFICATIONS Weight ............................................................................................................................................................................ 6 lbs. Blade Length .................................................................................................................................................................... 9 in. Edging Depth.................................................................................................
ASSEMBLY UNPACKING This product requires assembly. Carefully remove the items from the box. Make sure that all items listed in the packing list are included. Inspect the product carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. If any parts are damaged or missing, please call 1-800-242-4672 for assistance.
OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. ARROW GUIDE WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool.
OPERATION ADJUSTING DEPTH OF CUT ADJUSTING KNOB See Figures 4 - 5. The depth of cut is determined by the distance from the bottom of the wheel to the tip of blade. To adjust the blade depth: Stop the engine and remove the spark plug wire or disconnect from the power source. Loosen the adjusting knob and move the wheel arm up to increase the depth or down to decrease the depth. After adjustment is complete, tighten the adjusting knob securely.
MAINTENANCE WARNING: UPPER FLANGE WASHER When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. GEAR CASE WARNING: SLOTS Always wear safety goggles or safety glasses with side shields during tool operation. If operation is dusty, also wear a dust mask. FLANGE LOWER FLANGE WASHER WARNING: Fig.
MAINTENANCE REPLACING THE DEBRIS FLAP See Figure 9. Replace the debris flap if it is worn. Using a 10 mm wrench or socket, remove the hex nuts, washers, and debris flap. HEX NUT EDGER GUARD WASHER Install the new debris flap. This replacement part is available from the place of purchase, or by calling 1-800-242-4672. Replace washers and hex nuts. Tighten securely. ATTACHING THE STORAGE HANGER See Figure 10. There are two ways to hang the attachment for storage.
EXPLODED VIEW/PARTS LIST 29 27 28 26 25 24 23 22 16 21 16 17 16 15 18 14 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 12 30
EXPLODED VIEW/PARTS LIST Key No. Part Number Description 1 678018001 Blade Nut (M8)......................................................................................1 2 638017001 Cupped Washer ....................................................................................1 3 638006005 Blade .....................................................................................................1 4 678011001 Flange Washer ....................................................................
NOTES 14
WARRANTY LIMITED WARRANTY STATEMENT In addition, this warranty does not cover: A. Tune-ups – Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters B. Wear items – Bump Knobs, Outer Spools, Cutting Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower Fans, Blower and Vacuum Tubes, Vacuum Bags and Straps, Guide Bars, Saw Chains Techtronic Industries North America, Inc.
OPERATOR’S MANUAL Expand-it™ Edger Attachment UT15518F SERVICE For parts or service, contact your nearest Expand-it™ authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-800-242-4672 or visit us online at www.homelite.com. REPAIR PARTS The model number of this tool is found on a plate or label attached to the housing. Please record the serial number in the space provided below.
