OPERATOR’S MANUAL AIRgrip MultiTASKit™ EMM0001 Your product has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product.
TABLE OF CONTENTS n Introduction ..................................................................................................................................................................... 2 �n General Safety Rules ....................................................................................................................................................... 3 �n Symbols...........................................................................................................................
GENERAL SAFETY RULES n Always turn the laser level off when not in use. Leaving the tool on increases the risk of someone inadvertently staring into the laser beam. WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. n Do not operate the unit in combustible areas such as in the presence of flammable liquids, gasses or dust.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
FEATURES PRODUCT SPECIFICATIONS Vacuum Base Recommended Use................................................................................................................................................ Indoors Power Supply .................................................................................................................................2 AA, 1.5 Volt Batteries Battery Life ...................................................................................................
FEATURES MULTI-FUNCTION BASE CASE HOOK-AND-LOOP STRAP ROUGH-SURFACE ADAPTOR Fig. 2 KNOW YOUR MULTITASKIT™ LASER LEVEL ATTACHMENT See Figures 1 - 2. Before attempting to use this product, familiarize yourself with all operating features and safety rules. The laser level attachment emits a laser line of up to 30 feet and can be rotated 360˚. LIGHTING ATTACHMENT AIRGRIP™ VACUUM TECHNOLOGY The lighting attachment has three medium-intensity LED lights to provide light in dark work areas.
ASSEMBLY UNPACKING WARNING: This product has been shipped completely assembled. If any parts are missing, do not operate this tool. Please return to the place of purchase or call 1-800-525-2579 for assistance. n Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
OPERATION TURNING THE VACUUM BASE ON/OFF See Figure 4. Press the button located on the side of the vacuum base to turn it ON and OFF. Always wait for at least 5 seconds between stopping and restarting the unit. USING THE AIR-GRIP™ VACUUM BASE PUSH THE ON/OFF BUTTON TO TURN THE VACUUM BASE ON OR OFF See Figures 5 - 6. Vacuum grip technology allows the unit to be attached to most smooth surfaces. NOTE: The multi-function base is not used when mounting by vacuum grip.
OPERATION USING THE MULTI-FUNCTION BASE See Figures 8 - 9. To use the hook-and-loop strap or magnetic mounts, the multi-function base must be installed. To install the base: n While holding the vacuum base with the on/off button facing you, align the raised ridge on the multi-function base with the groove on the vacuum base. n Slide the two completely together. NOTE: If the multi-function base is seated correctly, the vacuum will not operate when the power is turned on.
OPERATION REMOVING/INSTALLING ATTACHMENTS See Figure 11. To install an attachment on the vacuum base, align the locking tabs on the desired attachment to the openings on the vacuum base so the molded-in arrow is directly centered above the battery door. Seat the attachment on the base and rotate until you hear the attachment click into place.
OPERATION USING THE LIGHTING ATTACHMENT See Figure 14. The lighting attachment uses three medium-intensity LED lights to provide extra illumination in dark workspaces. The light beam can be adjusted up to 90˚, and the lighting attachment can be rotated 360˚. Turn the lights on and off by depressing the on/off button located on top of the attachment. USING THE MAGNETIC TRAY ATTACHMENT See Figure 15. Position the tray in a horizontal or vertical position and tighten the locking knob to secure in place.
MAINTENANCE �n To clean the laser lens and lighting lens, if needed, use ONLY a soft cloth or cotton swab moistened with glass cleaner. WARNING: To avoid serious personal injury, always remove the batteries from the tool when cleaning or performing any maintenance. n Check the batteries regularly to avoid deterioration. Remove the batteries from the vacuum base, laser attachment, and/or lighting attachment, if you will not be using them for an extended time.
TROUBLESHOOTING Problem Vacuum not running Possible Cause Solution Batteries are low Replace batteries. Power is turned off Press on/off button. Laser line projection is weak Batteries are low Replace batteries. Laser line is hard to see Light in area is too bright Dim light in the work area or use laser-enhancing glasses. Light is not working Power is not “on” Press the on/off button. Batteries are low Replace batteries.
NOTES 15
OPERATOR’S MANUAL AIRgrip MultiTASKit™ EMM0001 • SERVICE This product has no serviceable parts. If unit fails due to normal wear and tear within two years of purchase, return with original receipt for a replacement unit at no charge. Please call 1-800-525-2579 for the nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO.
