TM 1
What’s in the Box? Note: Your configuration/camera will vary depending on your item options • 1 Color Sony CCD night vision weather proof backup camera • 1 16’ Camera Cable • 1 Power Connection Wire
Table of Contents Introduction ...................................................................................................4 Safety Information ..................................................................................5-7 Before Beginning Installation...................................................................8 Installation Guide ..................................................................................9-10 Adjustable Grid Line ...............................................
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplemental aid to the rear view mirror in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
Safety Information INSTALLATION • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before You Begin Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations.
Installation Guide Camera & Cable When installing the camera at the rear of the vehicle, remove the existing tailgate handle and replace with the tundra tailgate handle. Be sure to position the cable properly. The aviation camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts. Fasten all cables and secure all excess cable.
Installation Guide Safety • Before drilling, be sure no cable or wire is on the other side. • Feed as much cable as possible into vehicle & clamp securely. This reduces the possibility of cable being hooked or snagged. • Camera: Drill a 20mm (0.8in) diameter hole into vehicle body near the camera and bracket. Insert camera cable into vehicle (be careful not to kink cable) and fit grommet into hole. Apply sealant around grommet to increase resistance to water penetration.
Adjustable Grid Line Reverse With Confidence™ 11
Installation and Wiring Figure 1.1 Figure 1.
Splicing 1. 2. 3. 4. 5. 1. Red - Power (+) 2. Yellow - Video 3. Green - Mirror / Normal Imaging 4. White - Audio 5.
Positioning 14 REAR VIEW SAFETY
Troubleshooting No Image On Screen • Do a hard reset, unplug all cables and power cables, leave out for 1 minute and then re-connect them. • Check to ensure that the connection to the camera is tight. • Verify camera cable is plugged into port labeled Backup Camera • Verify that the green positive trigger on power harness is put to power 12v+.
Camera Dimensions 16 REAR VIEW SAFETY
Camera Camera Specifications Current Consumption Sensor Resolution (TV Lines) Minimum illumination Angle Effective Pixels TV System Video Output 1/3 SONY IC Sensor MAX: 150mA CMD-III, 1/4” 420 0.5 Lux 170° 648*488 NTSC Full color vdeo out: 1.
Warranty One Year Warranty Rear View Safety Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mis-handling of the electronic components. Rear View Safety Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.
