Instruction Manual 7” Digital Color Monitor With MirrorLink RVS-ML7 Before operating the Monitor, please read this manual thoroughly and retain it for future reference
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08-09 Sepecification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-15 Mirroring. .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The monitor is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. • If smoke or a burning smell is detected, disconnect the system immediately. • Do not install the monitor where it may obstruct driver's view or obstruct an air bag device. SAFETY INFORMATION • While installing the Rear View System be careful with the wire positioning in order to avoid wire • Use this product within the voltage range specified.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.888.881.2601 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor location. BEFORE YOU BEGIN Step 2: Install all cables in vehicle.
PRECAUTIONS 1. Do not expose the monitor to excessive heat/cold. The storage temperature of this device is -30°C~+80°C, and the operating temperature is -20°C~+70°C. The battery operating temperature is 0°C-70°C. Humidity is Rh 90%. 2. Never use this monitor near water or in damp locations. 3. Never use this monitor in environments with excessive moisture, dust or smoke. 4. Avoid dropping or hitting monitor. 5.
Operating Precautions 1. The monitor can be powered by a 12/24 volt battery, or the vehicle's electrical system. 2. Make sure all cables are connected properly. Improper cable connections may damage the monitor. Remove the power cable connections when not using the device. 3. The back-up battery can be recharged when the power is on. 4. When battery is fully charged, recharging will stop automatically. 5. If batteries are not used for a while, they may take longer to charge. Warning! PRECAUTIONS 1.
Specifications SPECIFICATIONS 1. Size: 7" Digital Color Monitor 2. Screen Ratio: 16:9 3. Resolution: 1024 X RGB X 600 4. Two AV inputs 5. Built-in Miracast 6.Built-in Speaker (Can Be Muted) 7. Auto Reverse Trigger Wire W/Adjustable Delay (0-10 Sec) 8. USB 2.0 Input 9. System: NTSC/PAL Auto Switch 10. OSD Menu/Remote Control 11. Automatic Shut Off After 15 Minutes Of Inactivity 12. Power Supply: DC12V 13. U-shaped Metal Bracket 14.
Monitor Remote Reverse With Confidence ™ SPECIFICATIONS 1. Volume Decrease/Setting Quantity Decrease/LEFT 2. Menu 3. Volume Increase/Setting Quantity Increase/RIGHT 4. Power 5. CH 1/UP 6. CH 2/DOWN 7. LINK/Confirm Menu 8. Remote Control Sensor 9. Bracket Knob 10. Reset Button 11.
Connection Menu SETTINGS Display options for each mode (AV1/AV2/LINK) can be individually set. After turning the system on, press "MENU" to enter menu and use "UP/ DOWN" to toggle menu options. Press “LEFT/RIGHT” on the remote control/monitor or “LINK” on the monitor to enter into current submenu. Then press “LEFT” and “RIGHT” to adjust setting. Press “MENU” to exit current menu. Volume: Press “LEFT” or "RIGHT" on the monitor/remote control to enter volume menu and also to adjust volume.
Reverse With Confidence ™ SETTINGS Brightness: Select option in the image menu, use “LEFT/RIGHT" to adjust brightness, and press “MENU” to confirm desired choice. Press “UP/ DOWN” to select next menu option. Contrast: Select option in the image menu, use “LEFT/RIGHT" to adjust contrast, and press “MENU” to confirm desired choice. Press “UP/DOWN” to select next menu option. Color: Select option in the image menu, use “LEFT/RIGHT" to adjust color, and press “MENU” to confirm desired choice.
SETTINGS Virtual Surround: Select option in the sound menu, and use "LEFT/ RIGHT" to toggle virtual surround on/off. Press “UP/DOWN” to select next menu option. Auto Volume: Select option in the sound menu, and use "LEFT/RIGHT" to toggle auto volume on/off. Press “UP/DOWN” to select next menu option. Speaker Mute: Select option in the sound menu, and use "LEFT/RIGHT" to toggle speaker mute on/off. Press “UP/DOWN” to select next menu option.
Reverse With Confidence ™ SETTINGS Power On Status: Select option in settings menu, and use "LEFT/ RIGHT" to toggle between three options (Last Memory/Standby/Power On). Press “UP/DOWN” to select next menu option. Blue Screen: Select option in settings menu, and use "LEFT/RIGHT" to turn blue screen on/off when there is no signal. Press “UP/DOWN” to select next menu option. ACC Line: Select option in settings menu, and use "LEFT/RIGHT" to open or close the ACC Line.
MIRRORING Miracast 1. Compatible with Airplay mirroring/latest iOS system. Compatible with iPad/iPhone/Mac notebook. 2. Supports Miracast Screen Mirroring, supports Android 4.2 (and above) Windows 8.1 system (computer should support HDCP). 3. Supports DLNA pushing. 4. Supports Tablet PC or notebook with WiDi function. 5. All windows devices can use Screen Share by installing AirParrot software. 6. Supports online movies, online TV channels, online radio and online webpage browsing. 7.
Miracast Basic Operating Introduction 1. Airplay Mirroring (for iPhone, iPad, Mac notebook) Find monitor’s hot spot (ex: DONGLE-ACA213068A04) from “Settings’’ of Apple devices and connect. Default password: 12345678 MIRRORING (Tips: the hot spot name has been displayed on the top of the screen and the password is behind the PIN) 1-2.
hot spot name, then start Airplay. The Apple device will share screen with the monitor.
Enter into Airplay interface, choose the device name and then start airply iOS 6: Double-click the HOME key or at the bottom of the main screen, you will see “Airplay”. Reverse With Confidence ™ MIRRORING iOS 7 (or above): From main screen slide screen up, Click “Airplay” and select the monitor's hot spot name. Exit mirror by swiping the “Mirroring” icon to the left.
MIRRORING Open internet browser and input web site IP “192.168.49.1” to enter into the setting page. Click the WiFi symbol, click “Scan” and find out available WiFi network (include hot spot from mobile device, such as smartphone, tablet PC and PC). For example: Click "QC" and enter password, then click “connect”. Open browser, input website IP: 192.168.49.
Click Scan, search the available wireless network Tips: IP is shown on the top of main interface. The monitor will be restarted and refresh automatically when connected to the WIFI network. If NO SIGNAL appears on the screen, wait for a few minutes. If NO SIGNAL still shows after a few minutes switch the signal channel on the monitor or remote.
After sucessfully connecting to the internet, the connected WIFI name after the WIFI icon and refresh the monitor’s IP address. At this time, the apple device have connected the WIFI network (QC), and can share the screen with “Mirroring”. MIRRORING Tip: After initial WIFI setup, any Apple device can Airplay Mirroring directly after connected this WIFI network, no need setup again. If you want to exit the network, please input the new IP on the top of screen in the browser, and choose "forget". 2.
2-2. Miracast Mirroring ( for Windows 8.1 tablet ) 2-2-1.
2-2-2. From device list, select “Project” MIRRORING 2-2-3. The first time to use project function, you need to add a wireless display. 2-2-4. After adding the monitor, the computer will automatically find the monitor hotspot. After this occurs click add.
Reverse With Confidence ™ MIRRORING Tip 1: The device DONGLE-ACA213068A04 in this manual is an example device. Different monitors will have different names. Please refer to the displayed name on the top of main interface. Tip 2: When adding a device, “press the button on your DONGLE-ACA213068A04” will appear. Ignore this warning. 2-2-5. After successfully connecting you may start mirroring. Tip 3: After intial connection, just click Device—Project to find DONGLE-ACA213068A04.
3.DLNA Video Pushing (Apple and Android devices) Some devices have a built-in DLNA function, allowing you to push video from your wireless devices (Apple or Android) onto the monitor. You can also download third party DLNA software in the app store. If you have DLNA function, push video by selecting device. Note: If device is not connected to WiFi, you may only push local video. 4. OTA Upgrade 4-1. On connection with WiFi screen "New update found, press the button to update.
ware version will display on the top right corner of the screen.
Miracast Restore Press reset button on the back of the monitor for 10 seconds to delete Miracast Link user data and restore to factory settings. Tip: The monitor will be restarted and refresh screen automatically after restoring to factory settings. If NO SIGNAL appears on the screen, wait for a few minutes. If NO SIGNAL is still on screen after a few mintues, switch the signal channel on the monitor or remote. Miracast FAQ TROUBLESHOOTING 1. Video is not smooth a.
Notes TROUBLESHOOTING Reverse With Confidence ™ 29
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
