Instruction Manual G-SERIES Backup Camera System with Compass and Temperature RVS-776718-CT Reverse With Confidence ™ Rear View Safety, Inc.
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . 07 Installation Guide. . . . . . . . . . . . . . . . . . . . .
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury. However, you the driver, must use it properly.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly.
INSTALLATION GUIDE Clip-On Monitor 1. The Mirror Monitor attaches to the existing rear view mirror in vehicle with the pressurized clips on the back of the monitor. 2. Attach monitor to existing mirror, and adjust mounting angle to allow optimum driver viewing comfort. Camera & Cable Be sure to position the cable properly. The aviation camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements.
Grid Lines Generally, to help drivers estimate the distance from obstacles, there are three lines for reference- red, yellow, and green. Those three lines are displayed on the monitor when car is reversing. The green line is 3M from the back of the car and the yellow line is 6.5 ft. The distant red line is 1M from the backside of car while the close red line is 0.4M. Both reference lines on the left and right should leave 0.2M space from the car. INSTALLATION AND WIRE ADJUSTABLE GRID LINE FIGURE 1.
FIGURE 2.1 HOW TO WIRE + SPLICING HOW TO WIRE + SPLICING FIGURE 2.2 1. RED- Power (+) 2. YELLOW- Video 3. GREEN- Mirror / Normal Imaging 4. WHITE- Audio 5.
Digital Compass Calibration 5. Press “SEL/REC” to select the “CALIBRATION”, press UP/DOWN, select “OFF” 1-4. 2. Press “ SEL/REC” to select the “CALIBRATION”, the default mode is “OFF”, press “DOWN” select “AUTO” 1-2. Caution 3. Drive your vehicle in at least 2 circles counterclockwise, allowing 90 seconds to complete one circle. 4. Keep your circle radius close to 5 meters and your speed less than 10km/h for the most accurate calibration. 1-3. 14 Rear View Safety 1.
Temperature Sensor Installation Q&A TEMPERATURE SETTING The Distribution Of Magnetic Fluxline Temperature Setting (Option) We do not recommend using the compass in an area with high magnetic lines of flux. For example, in the north of Canada. Press “MENU” to enter into “SETTING” menu, and press “SEL/REC” button to choose the “TEMP UNIT”. Press UP/DOWN to switch between °F and °C 4-1.
MAGNETIC FLUXLINE DISTRIBUTION MAGNETIC FLUXLINE DISTRIBUTION 18 Rear View Safety Reverse With Confidence ™ 19
About Our Monitor About Camera 10.25” SPECIFICATIONS: 20 Screen Size: Display Screen: Display Resolution: Aspect Ratio: Color Depth: Pixel Pitch (mm) Power Consumption: Working Voltage: 4.3” TFT-LCD 400(H)x234(V) 16:9 16.7M dithering 0.219x0.
Camera Installation No Image On Screen • Do a hard reset, unplug all cables and power cables, leave out for 1 minute and then re-connect them • Check to ensure that the connection to the camera is tight • Verify that the green positive trigger on power harness is put to power 12v+ Mounting Position view angle installation 22 position Rear View Safety • Verify cable is connected to monitor • Verify camera is connected to cable • Connect known working camera and cable to monitor • Verify Green trigger
ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
A Safe Fleet Brand If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
