Product Manual Installation Instructions Rear View Camera Systems Model # RVS-091407 © 2009-2013 Rear View Safety Inc.
Table of Contents Introduction ......................................................4 Safety Information .........................................5 Package Contents ............................................6 Settings/ Maintenance .....................................7 Installation Guide .............................................8 Positioning .....................................................11 Pairing and Connecting .................................12 Operation Guide ..............................
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System. With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Safety Info ■ Place the monitor away from direct sun light, heat, water or moisture.This product is made with precise electronic components. Handle with care. Improper use can cause a malfunction. ■ Firmly fix the monitor stand to secure location. ■ While installing the Rear View System be careful with the wire positioning in order to avoid wire damage.
Package Contents 6
Settings You can adjust the contrast and brightness of the Monitor according to your desired level. Note: Contrast and Brightness setting ONLY works while the backup image is on the screen. 1.To Adjust Contrast Press the arrow key up or down The system has 2 program functions: 1. Camera Setting Push the Menu to pair, pairing mode will enable for 30 seconds 2. System setting A.Power saving push menu to change the selection and hold the Menu for long to exit B.
Installation Diagram Diagram A Dc female BMW male Diagram B Dc male BMW female Diagram C Fuse DC12V GND (Red) (Black) DC12V GND (Red) (Black) Mounting the monitor: The monitor either mounts on to, or replaces the existing rear view mirror in your vehicle (see item options.) The clip-on monitor uses a special pressurized mechanism (see diagram A) which clips onto the existing rear view mirror.
Installation Guide 1. Locate the reverse taillights wiring behind your reverse light. You may need to remove the interior panel in order to locate. You only need to attach the signal booster power wire to ONE of the reverse lights, not both. If you cannot manually locate the tail light cables, please contact the vehicle manufacturer or reference a wiring diagram for your vehicle 2. At your taillight, remove the light bulb socket from the reverse light housing. 3.
Installation Guide Installation 6. Plug the attached wire from the Camera into the Wireless . Transmitter. Ensure that the wires are not tangled. 7. While sitting in the driver’s seat of the car with the key in the ignition position. The monitor will automatically start when vehicle is put in reverse. If when you place the vehicle in reverse there is no image, you may need to pair the camera with the monitor 8. Put the vehicle in reverse.
Positioning 11
Pairing & Connecting Pairing is not necessary as the unit has already been paired. If you are not able to connect the camera, please try to pair the camera by the following steps: 1. Press “Pair” button on the Wireless Digital Transmitter. You will see the LED Blinking in RED/BLUE. The unit will remain in Pair mode for 30 seconds 2. Go to the monitor and do the following step: a. Press “Menu” b. Go to “Pair Camera” d.
LCD Parametres TFT LCD Digital Monitor Screen Size 4.3" Dot Resolution 800 X 3 (RGB) X480 Display Format 16:9 Display Brightness 400 Viewing Angle 90° Min Video Input 1 channel Video Source 1Vp-p, 75Ω Power Supply DC 12V Power Consumption 5W Operating Temperature 10°C ~ +65° C Video System Auto NTSC/PAL Overall Dimensions 10” (L) x 3.5” (H) x 1” (D) Weight 400G Impact Rating 5G Active Area 154.08(H) x 86.
Monitor Dimensions Display Image Size: 4.2 x 2.
Product Info Camera MT9V136 Picture Elements 250,000 pixels Gamma Correction r=0.45 to 1.0 Image Sensor 480TV lines NTSC:510(H)*492(V) Lens 2.1mm View Angle 130° Sync System Internal Synchronization Infra-red distance 30 Feet (9 Infrared IR) Usable Illuminatiom 0 Lux (IR On) Power Source DC 12V(+/- 10%) S/N Ratio More than 48dB Electronic Iris 1/50, 160-1/100,000sec Video Output 1Vp.
Warranty One Year Warranty Rear View Safety Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mis-handling of the electronic components. Rear View Safety Inc. is not responsible for consequential damages of any kind.
™ Rear View Safety, Inc. 1680 Atlantic Ave # 301 Brooklyn, N.Y. 11213 (800) 764-1028 www.rearviewsafety.
