Mountain Modern Door INSTALLATION INSTRUCTIONS
MOUNTAIN MODERN Recommended Tools Drill with 1/8”, 1/4” Drill Bits and Phillips Screw Bit 5.5mm or 7/32” Allen Wrench Socket Wrench with 7/16 and 9/16” Socket Tape Measure Pencil Level MOUNTAIN MODERN Parts VERSION 3 2 RUSTICAHARDWARE.com 2017 A. 03 B.
MOUNTAIN MODERN Parts C. D. E. F. G. H. I. J. K. L. M. VERSION PARTS A. Door Assembly B. Header (Optional) C. Lag Screw D. 1” Washer E. #6x1-1/4” Flat Head Wood Screw F. #8x3/4” Flat Head Wood Screw G. #8x3/4” Round Head Wood Screw H. Hard Stop & Rubber Bumper I. Spacer J. Anti-Jump Block and Socket Screw K. Adjustable Wall-Mount Door Guide L. Track M. Door Pull 3 RUSTICAHARDWARE.com 2017 3 03 Use teamwork - We recommend two people for this build.
MOUNTAIN MODERN Installation Instructions FIRST THINGS FIRST Check to see if the sill or floor below the track area is level. If the sill or floor rises more than 1/2” the panel or door may rub or not slide open completely. If the sill or floor is not level, measure from the highest point of the sill or floor surface to the recommended track placement and adjust track placement accordingly. Ensure the track will be installed onto wall studs.
MOUNTAIN MODERN Installation Instructions 6. Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3). Figure 3 7. Attach one end of the track to the wall with one hard stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten. 8. Repeat step 7 for the other end of the track. Figure 4 9. Install remaining spacers with lag screws and washers (provided) using a 9/16” socket wrench (Figure 5). Tighten all lag screws.
MOUNTAIN MODERN Installation Instructions TRACK INSTALLATION WITH HEADER FIRST THINGS FIRST Check to see if the sill or floor below the track area is level. If the sill or floor rises more than 1/2” the panel or door may rub or not slide open completely. If the sill or floor is not level, measure from the highest point of the sill or floor surface to the recommended track placement and adjust track placement accordingly. TRACK PLACEMENT 1-5/8” 1.
MOUNTAIN MODERN Installation Instructions 2” 4. Lay the header on a flat clean surface. Using a measuring tape, measure 2” from the bottom of the header. Draw a line the length of the header with a pencil (Figure 3). Figure 3 5. Lay the track on top of the header, centering it with the line drawn on the header. Ensure the track is 2” from either end of the header. Using a pencil, mark the hole positions in the track onto the header (Figure 4). Set the track aside. Figure 4 1” 1” VERSION 6.
MOUNTAIN MODERN Installation Instructions 7. Drill pilot holes for the stud installation in the header with an 1/8” drill bit (Figure 6). Figure 6 8. Align the line on the wall with the line made on the header in step 4. Ensure pilot holes align with wall studs (Figure 7). 9. Install header using 3” wood screws (F.) (Figure 7). Figure 7 VERSION 10. Header installation is complete (Figure 8). Proceed with track installation on pages 4 and 5. 3 03 Figure 8 2017 8 RUSTICAHARDWARE.
MOUNTAIN MODERN Installation Instructions PULL INSTALLATION NOTE 3’ (feet) or 36” (inches) The center point of the door pull should be three feet or 36” above the bottom edge of the door. Avoid placing the door pull too close to the edge of the door. Placing the pull too close to the edge can damage both door and pull. 1. Lay the door (A.) facing up on a clean, stable surface. Figure 1 2.
MOUNTAIN MODERN Installation Instructions DOOR INSTALLATION � 1. Hang the door on the track (Figure 1). Figure 1 ANTI-JUMP BLOCK INSTALLATION 2. Install the anit-jump block (J.) on the back of the hanger using the provided socket screw (Figure 3). 3. Repeat for the opposite end of the door. DOOR GUIDE INSTALLATION Figure 3 4. Slide the door to the open position (Figure 4). 5. Align the door guide (K.) slightly below the door’s bottom edge ensuring the door can slide through the guide without scraping.
WE LOVE WHAT YOU ARE DOING WITH THE PLACE CONGRATULATIONS ON YOUR DECISION TO BRING HOME AN AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY. WE HOPE YOUR MOUNTAIN MODERN Door BRINGS ART AND FUNCTION INTO YOUR LIFE. Designed and crafted entirely in the U.S.A. don’t be a stranger. follow us on social media. support@rusticahardware.
