How to Guide

ManualsBrandsRust-Oleum ManualsCar Exterior CleanersHDLCAL

TECHNICAL DATA WNW-02

WIPE NEW

HEADLIGHT RESTORE

Form: GDH-1080

Rev.: 032916

.DESCRIPTION AND USES .

Rust-Oleum

Wipe New

Headlight Restore is a long-lasting

solution that restores clarity to aging and fogging headlights.

.FEATURES .

 Restores illumination and visibility

 Easy-to-use, one wipe solution

 Long lasting shine – protects through 100 car washes

.PRODUCTS .

SKU Description

HDLRTLKIT Wipe New 6PK Headlight

HDLCAL Wipe New 6PK Headlight CA Com

..PRODUCT APPLICATION .

APPLICATION CONDITIONS

Use when temperatures are between 40°F and 90°F (4°C and

32°C). Use in well ventilated and covered areas away from the

sun. Do not apply Wipe New to hot surfaces or in direct sunlight.

Ensure surface is clean, dry and cool to ambient temperature

before applying Wipe New.

SURFACE PREPARATION

Prep the exterior of all lenses intended for application at

the same time so that one Wipe-It™ can be used to treat

all lenses. Once the Wipe-It™ is opened it begins to cure.

Do not open the Wipe-It until needed and complete the

application within a few minutes.

Wash the intended surface thoroughly with a standard soap,

cleaner or car wash (free of wax, moisturizers or other additives).

Rinse and let dry. For best results, apply a degreaser to heavily

worn areas to fully clean the surface.

To determine whether you need to use the Professional

Lens Polishing Pad, pour water onto your headlight lens.

The way the lens looks when wet is the way it will appear

once treated with Wipe New. If the lens appears crystal

clear when wet (and hazy only when dry), then you do not

need to use the Lens Polishing Pad. Simply wash the lens

with soap and water, rinse, and apply Headlight Restore. If

the lens appears cloudy or hazy when wet; the Lens

Polishing Pad will be required.

Wet the headlight lens with water and use the green side

of the Lens Polishing Pad to wet sand the headlight lens

and remove oxidation. Ensure the lens remains wet while

using the Polishing Pad. The oxidation coming off the lens

will appear as a brownish colored liquid; continue to rub

until this visual indicator is no longer present.

IMPORTANT: Do not allow the Polishing Pad to come into

contact with painted surfaces as it may scratch these

surfaces.

..PRODUCT APPLICATION (cont.) .

SURFACE PREPARATION (cont.)

Re-wet the headlight lens and use the gray side of the

Professional Lens Polishing Pad to further polish the

headlight lens.

Dry the lens thoroughly with the included microfiber towel

and inspect the surface to ensure oxidation has been

removed. If not, repeat steps above on any missed spots.

When you can see through the lens while wet, you are

ready to apply Wipe New. Ensure all lenses are 100% dry

prior to proceeding to application.

APPLICATION

Put on the chemical resistant gloves and ensure that you are in

a well ventilated area. Make sure headlight lenses are

completely dry. Tear open the Wipe-It packet, pull out the

applicator cloth and carefully wipe the lens ONE TIME in a single

wipe, from one row to the next, with a slight overlap (like mowing

a lawn) until the surface is completely coated. Be careful to not

get any Wipe New on the surrounding paint. If treating multiple

lenses, do so before the Wipe-It dries out. If Wipe New comes in

contact with an unintended surface such as paint; wipe it off

immediately with a dry cloth. Within an hour of application (while

still undergoing initial cure), acetone may be used to remove

Wipe New from a painted surface, but not from plastic or any

nonmetal surface. Because acetone can damage vehicle parts

or paint, it should be used only after checking with the vehicle

manufacturer or a Certified Paint Professional as to how to best

apply or remove product. After Wipe New has cured, removing it

will require the use of a fine polishing compound or high grit

automotive sandpaper.

DRY TIME

The headlights will dry to the touch in about 1 hour. Do

not allow treated lenses to come in contact with direct

moisture (rain, dew, etc.) for 24 hours. Store excess

product in a cool, dry place.

COVERAGE

One Wipe-It contains enough Wipe New to treat the exterior of

multiple headlight lenses.

DISPOSAL

When finished, set the applicator cloth in a location out of the

reach of children and allow it to dry completely prior to discarding

(a few hours).

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA WNW-02 WIPE NEW® HEADLIGHT RESTORE .DESCRIPTION AND USES ® ..PRODUCT APPLICATION (cont.) . ® SURFACE PREPARATION (cont.) Rust-Oleum Wipe New Headlight Restore is a long-lasting solution that restores clarity to aging and fogging headlights. .FEATURES    . Re-wet the headlight lens and use the gray side of the Professional Lens Polishing Pad to further polish the headlight lens. .
PAGE 2
TECHNICAL DATA WIPE NEW® HEADLIGHT RESTORE PHYSICAL PROPERTIES . HEADLIGHT RESTORE Resin Type Siloxane Polymer NA Pigment Type None Volatile Organic Compounds Practical Coverage at Recommended DFT Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity California - N-Butyl Acetate, Parachlorobenzotrifluoride Parachlorobenzotrifluoride Solvents Contains enough to treat the exterior of multiple headlight lenses.