How to Guide

ManualsBrandsRust-Oleum ManualsSpray PaintAS2144838

AEROSOLS TECHNICAL DATA IC-02

AS2100 SYSTEM

ANTI-SLIP AEROSOL

Form: GDH-1096

Rev.: 110916

.DESCRIPTION AND USES .

Anti-slip aerosols provide a slip resistant surface for most

interior/exterior metal, concrete, ceramic and wood surfaces.

These aerosols apply easily and provide uniform coverage with a

low-luster. They dry to a tough, durable finish that resists peeling

and cracking while providing resistance to gasoline, oil and other

harsh substances.

Use anti-slip aerosols wherever a slip-resistant surface is desired.

The Anti-slip aerosols are suitable for use on stairs, pool decks,

ramps, walkways and much more.

This product complies with USDA FSIS regulatory sanitation

performance standards for food establishment facilities. This

coating is impervious to moisture and easily cleaned and

sanitized.

.PRODUCTS .

SKU Description

AS2102838 Clear

AS2144838 Safety Yellow

AS2178838 Black

AS2185838 Gray

AS2192838 White

PACKAGING .

6 aerosols per carton (15 fl. oz. container)

.PRODUCT APPLICATION .

SURFACE PREPARATION

ALL SURFACES: Remove all dirt, grease, oil, salt and

chemical contaminants by washing the surface with Krud

Kutter

Cleaner Degreaser, commercial detergent or other

suitable cleaner. Mold and mildew must be cleaned with a

chlorinated cleaner or bleach solution. Rinse with fresh

water and allow to thoroughly dry.

STEEL: Hand tool clean (SSPC-SP-2) or power tool clean

(SSPC-SP-3) to remove loose rust, mill scale, and

deteriorated previous coatings.

PREVIOUSLY COATED: Previously coated surfaces must

be sound and in good condition. Smooth, hard, or glossy

finishes should be scarified by sanding to create a surface

profile.

APPLICATION

Apply only when air and surface temperatures are

between 50-100ºF (10-38ºC) and surface temperature is

at least 5ºF above dew point.

DRY AND RECOAT TIMES

Can be recoated in 1-2 hours and can be walked on in 24-

48 hours. Allow more time in cooler temperatures. Apply a

Rust-Oleum top coat anytime after 1 hour. Maximum

topcoat adhesion and durability will be achieved in 5-7

days.

CLEAN-UP

Clean valve immediately after use by turning can upside

down and depressing spray button for 3-5 seconds.

Properly discard empty container. Do not burn or place in

trash compactor. Empty container can be recycled.

CLOGGING

If clogging develops, twist off spray button and clean with

thinner. DO NOT insert pins or any other object into the

valve can opening. Replace spray button carefully, be sure

the tip is facing away from you.

Summary of content (2 pages)

PAGE 1
AEROSOLS TECHNICAL DATA IC-02 AS2100 SYSTEM ANTI-SLIP AEROSOL .DESCRIPTION AND USES . .PRODUCT APPLICATION SURFACE PREPARATION Anti-slip aerosols provide a slip resistant surface for most interior/exterior metal, concrete, ceramic and wood surfaces. These aerosols apply easily and provide uniform coverage with a low-luster. They dry to a tough, durable finish that resists peeling and cracking while providing resistance to gasoline, oil and other harsh substances.
PAGE 2
TECHNICAL DATA AS2100 SYSTEM ANTI-SLIP AEROSOL PHYSICAL PROPERTIES . ANTI-SLIP AEROSOL Resin Type Chain Stop Alkyd Pigment Type Varies with color Solvents Acetone, Xylene, Toluene MIR Maximum value of 2.45 Fill Weight 15 oz. Solids by weight 18-25% (varies by color) Recommended Dry Film Thickness (DFT) Per Coat Coefficient of Friction 1-2 mils (25-50µ) Dry 0.72 Wet 0.85 Approximately 14 ft.2/can (1.