Technical Specifications
TECHNICAL DATA
SRU-04
STOPS RUST
SATIN BRUSH
DESCRIPTION AND USES
R
u
s
t
-
O
l
e
u
m
®
Stops
R
u
s
t
®
Satin Finish provides a classic
l
o
w
sheen and durable finish. This smooth, protective enamel
o
ff
e
r
s
excellent coverage, chip resistance and color retention.
U
se
on interior/exterior metal or wood surfaces. For even
l
o
ng
e
r
,
lasting protection, use a Stops
R
u
s
t
®
primer first. Not for use on
galvanized s
t
ee
l
.
PRODUCT
APPLICA
TION
PAINTING
C
O
N
D
I
T
I
O
NS
Apply only when air and surface temperatures are above
50
°
F
(10°C) and humidity is below 85% to ensure proper drying.
D
o
not apply to surfaces that will exceed 200°F (93°C). Do not use
on galvanized s
t
ee
l
.
SURFACE
P
R
E
P
A
R
AT
I
O
N
ALL SURFACES:
Remove all dirt, grease, oil, salt and
c
h
e
m
i
c
a
l
contaminants by washing the surface with a
c
o
mm
e
r
c
i
a
l
detergent or other suitable cleaning method. Rinse
t
h
o
r
o
ugh
l
y
with fresh water and allow to fully dry. All surfaces must be d
r
y
at time of
a
pp
li
c
a
t
i
o
n
.
STEEL:
Scrape and wire brush or power tool clean to
r
e
m
ove
loose rust, scale and deteriorated previous coatings. Use
7769
Rusty Primer for sound rusted or clean metal before
a
pp
li
c
a
t
i
o
n
of a finish coat. 7780 White Clean Primer is best for clean
m
e
t
a
l
but may be used on sound rusted metal as
w
e
ll
.
PRODUCT
APPLICA
TION
PREVIOUSLY COATED:
Previously coated surfaces must be so
und
and in good condition. Smooth, hard, or glossy finishes should be
scarified by sanding to create a surface profile.
T
h
e
Stops
R
u
s
t
®
Satin Finish is compatible with most coatings, but a
test patch is suggested. WARNING! If you scrape, sand or
r
e
m
ove
old paint from any surface, you may release lead paint du
s
t
.
LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
S
E
R
I
OU
S
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
C
HI
L
D
R
E
N
.
PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.
Wear a
NIOSH approved respirator to control lead exposure. Clean
up
carefully with
a HEPA
vacuum and a wet mop. Before you s
t
a
r
t
,
find out how to protect yourself and your family by contacting
t
h
e
National Lead Information Hotline at
1
-
800
-
424
-
L
E
A
D
or log on
t
o
www
.
e
p
a
.
g
ov
/
l
ea
d
.
P
A
I
N
T
I
N
G
Before using, stir thoroughly to ensure any settled pigment is
r
e
-
dispersed. If necessary, thin the material with acetone. For b
r
u
s
h
or roller, thinning is not normally required. For air spray, thin up
to 15% with acetone. Do not thin with gasoline, lacquer
t
h
i
nn
e
r
,
turpentine, etc. For airless spray, thinning is not normally
r
e
qu
i
r
e
d
.
Apply with a good quality brush, roller or spray gun
.
Brush:
Use light, even strokes. Excessive brushing reduces
film
thickness and p
r
o
t
e
c
t
i
o
n
.
Roller:
A
3/8"
nap roller should be used on rough s
u
r
f
a
c
es
.
Cover approximately one square yard at a time. Roll a
w
ay
from previously coated area and work back to
it
for a
un
i
f
o
r
m
appearance. Use a brush on crevices and sharp e
dg
es
.
Spray Gun:
Follow spray gun directions carefully. Always
k
ee
p
the gun ten to twelve inches from the surface and in motion
w
h
il
e
s
p
r
ay
i
ng
.
C
L
E
A
N
-
U
P
Clean brush and tools with Mineral
S
p
i
r
i
t
s
.
1