Technical Specifications
TECHNICAL DATA
SRU-08
STOPS RUST
BRIGHT COAT METALLIC
SPR
A
YS
DESCRIPTION AND USES
R
u
s
t
-
O
l
e
u
m
®
Stops
R
u
s
t
®
Bright Coat Metallic Sprays a
r
e
designed to provide a durable protective coating with
ex
c
e
ll
e
n
t
resistance to rust, and excellent resistance to abrasion,
f
a
d
i
ng
,
chipping, and dulling. These sprays apply easily,
p
r
ov
i
d
e
excellent coverage and dry fast to a tough attractive
fi
n
i
s
h
.
Aluminum is appropriate for outdoor metal surfaces
w
h
e
n
primed first. Gold, Chrome, and Bronze should be used
i
nd
oo
r
s
as they will tarnish
if
placed outdoors. These sprays feature a
comfort tip with a wider finger pad to reduce fatigue caused b
y
continuous spraying and the
a
n
y
-
a
ng
l
e
tip which allows you
t
o
spray at any a
ng
l
e
.
PRODUCT
APPLICA
TION
PAINTING
C
O
N
D
I
T
I
O
NS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50°F (10°C) a
nd
90°F (32°C) and humidity is below 65% to ensure p
r
o
p
e
r
drying. Do not apply to surfaces, when heated, exceed
200
°
F
(93°C). Avoid spraying in very windy and dusty
c
o
nd
i
t
i
o
n
s
.
Cover surrounding area to protect from spray
m
i
s
t
.
SURFACE
P
R
E
P
A
R
AT
I
O
N
Remove all dirt, grease, oil, salt and chemical
c
o
n
t
a
m
i
n
a
n
t
s
by washing the surface with a commercial detergent, or other
suitable cleaning method. Rinse with fresh water and allow
t
o
thoroughly dry. Remove loose paint and rust with a wire
b
r
u
s
h
or sandpaper. Previously coated surfaces must be sound a
nd
in
good condition. Smooth, hard, or glossy finishes should be
scarified by sanding to create a surface profile. WARNING!
If
you scrape, sand, or remove old paint, you may release
l
ea
d
dust.
LEAD IS TOXIC.
Contact the
U
.
S
.
E
P
A
/
Lea
d
I
n
f
o
r
m
a
t
i
o
n
Hotline at
1
-
800
-
424
-
L
E
A
D
or log on to
www
.
e
p
a
.
g
ov
/
l
ea
d
.
PRODUCT APPLICATION
(cont.)
PRIMING
Use of a
R
u
s
t
-
O
l
e
u
m
®
primer provides added corrosion p
r
o
t
e
c
t
i
o
n
,
excellent adhesion and hiding and is especially recommended
f
o
r
bare wood and metal. The following primers are
r
e
c
o
mm
e
nd
e
d
.
7769 Rusty Metal
P
r
i
m
e
r
7780 Clean Metal
P
r
i
m
e
r
P
A
I
N
T
I
N
G
Shake can vigorously for one minute after the mixing ball b
e
g
i
n
s
to rattle. If mixing ball fails to rattle
DO NOT STRIKE CAN.
C
o
n
t
a
c
t
R
u
s
t
-
O
l
e
u
m.
Shake often during use. Hold can upright
10-16"
from surface and spray in a steady
back-and-forth motion, slightly
overlapping each stroke. Keep the can the same distance from
t
h
e
surface. Keep the can in motion while s
p
r
ay
i
ng
.
Apply two or
m
o
r
e
light coats a few minutes apart to avoid drips and runs. Do not use
near open
fl
a
m
e
.
DRY &
R
EC
O
AT
Dry and recoat times are based on 70°F and 50%
r
e
l
a
t
i
ve
humidity. Allow more time at cooler temperatures. Dries to
t
o
u
c
h
in 1 hour and primers may be top coated immediately. Apply a
second coat within 1 hour or after 48 hours.
A clear coat finish
i
s
not
r
ec
o
mm
e
nd
e
d
.
C
L
E
A
N
-
U
P
Wipe off tip before storing.
C
l
ea
n
-
up
wet paint with xylene
o
r
mineral spirits. Properly discard empty container. Do not burn
o
r
place in home trash
c
o
m
p
a
c
t
o
r
.
C
L
OGG
I
N
G
If the valve clogs, twist and pull off spray tip and rinse in a
so
l
ve
n
t
such as mineral spirits. Do not insert any object into can valve
op
e
n
i
ng
.
1