Manualshelf

Technical Specifications

ManualsBrandsRust-Oleum ManualsExterior Oil-Based PaintStops Rust® Professional Gloss Protective Enamel Paint Masstone Tint Base - 1 gal.
12
TECHNICAL DATA
PRO-02
PROFESSIONAL HIGH PERFORMANCE
DTM ALKYD ENAMEL (450 VOC)
1
DESCRIPTION AND USES
Rust-Oleum
®
Professional DTM Alkyd Enamels are oil-
modified alkyds with excellent rust prevention when applied
directly to metal. They also offer excellent coverage, chip
resistance and color retention. Not for use on galvanized
steel.
PRODUCTS
DESCRIPTION
GALLON
QUART
Rusty Metal Red Primer
7769402
-----
White Clean Metal Primer
7780402
Aluminum Primer
8781402
Aluminum
7715402
-----
Safety Blue
7524402
-----
Royal Blue
7727402
V7727502
Hunter Green
7738402
V7738502
Safety Yellow
7543402
202191T
Dark Brown
7748402
-----
Safety Orange
7555402
-----
Safety Red
7564402
202192T
Regal Red
7765402
-----
Almond
7770402
V7570502
Sand
7771402
-----
Leather Brown
7775402
V7575502
Flat Black
7776402
7578502
Black
7779402
V7579502
Light Machine Gray
7781402
-----
Smoke Gray
7786402
V7586502
Flat White
7790402
7590502
White
7792402
V7592502
Semi-Gloss White
239076
243996T
Semi-Gloss Black
239078
243995L
Red Tint Base
7505418
-----
Yellow Tint Base
7506418
-----
Masstone Tint Base
7507418
-----
Pastel Tint Base
7509418
-----
PRODUCT APPLICATION
SURFACE PREPARATION
Clean surface with soap and water, rinse and let dry.
Remove loose paint and rust with a wire brush or sandpaper.
Lightly sand glossy surfaces.
WARNING!
If you scrape, sand, or remove old paint, you my
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION (cont.)
Wear a NIOSH-approved respirator to control lead exposure.
Clean up carefully with a HEPA vacuum and a wet mop. Before
you start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-424-
LEAD or log on to www.epa.gov/lead.
APPLICATION
Apply only when air and surface temperatures are between
32-90ºF (0-38ºC) and humidity is below 65% to ensure
proper drying. Do not apply to surfaces that, when heated,
exceed 200ºF (93ºC) or galvanized metal. Professional DTM
Alkyd Enamels can be used over most latex or oil paints.
Professional DTM Alkyd Enamels and Primers are not
recommended for water immersion.
Mix thoroughly to ensure any settled pigment is re-dispersed
before using. Thin material, only if necessary, with acetone.
For brush or roller, thinning is not normally required. For air
spray, thin up to 1-½ to 2 pints per gallon. Do not thin with
gasoline, lacquer thinner, turpentine, etc. For airless spray,
thinning is not normally required. Apply with a good quality
brush, roller or spray gun.
Brush: Use light, even strokes Excessive brushing reduces
film thickness and protection.
Roller: The rougher the surface, the longer the roller nap
should be. Cover approximately one square yard at a time.
Roll away from previously coated area and work back o it for
a uniform appearance. Use a brush on crevices and sharp
edges.
Spray Gun: Follow spray gun directions carefully. Always
keep the gun ten to twelve inches from the surface and in
motion while spraying.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 2-4 hours, to handle in 5-10 hours and
is fully dry after 24 hours. Recoat after 24 hours.
CLEAN-UP
Clean brush, roller and other tools with mineral spirits.

Summary of content (2 pages)