Use and Care Manual

TECHNICAL DATA
CHD-07
CHALKED
ULTRA MATTE SPRAYS
1
Form: GDH-1027
Rev.: 020718
DESCRIPTION AND USES
Rust-Oleum
®
Chalked Ultra Matte Sprays create an ultra
matte finish with excellent coverage and adhesion on
furniture and home décor. Chalked Ultra Matte Sprays
provide one coat coverage on most surfaces without special
surface preparation or priming. It can be painted or
distressed, giving the project a one of a kind look. It is
suitable for use on wood, metal, ceramic, glass, canvas and
more.
Chalked Ultra Matte Sprays feature an advanced spray
system that allows you to spray at any angle, even upside
down for those hard to reach areas. A comfort spray tip with
a wider finger pad to reduce fatigue caused by continuous
spraying.
Some plastics made of polyethylene such as Little Tikes
®
children’s products are manufactured in a way that may
hinder maximum paint adhesion. Test this product in an
inconspicuous area to test for compatibility on the surface.
Not for use on galvanized metal.
PRODUCTS
SKU
DESCRIPTION
302590
Charcoal
302591
Linen White
302592
Aged Gray
302593
Country Gray
302594
Blush Pink
302595
Serenity Blue
302596
Chiffon Cream
302597
Tidal Pond
302598
Coastal Blue
302599
Matte Clear
329193
Farmhouse Red
329194
Cocoa Bean
PRODUCT APPLICATION
Use in a well ventilated area such as an open garage. Apply
when temperature is between 10-32°C and humidity is below
85% to ensure proper drying. Avoid spraying in very windy,
dusty conditions. Cover the surrounding area to protect from
spray mist.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with soap and water and let dry.
Remove loose paint and rust with a wire brush or sandpaper.
Lightly sand glossy surfaces. Remove any wax by lightly
wiping the surface with mineral spirits.
PRODUCT APPLICATION (cont.)
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop.
PRIMING
Priming is not required for most surfaces. For excellent
coverage, use of a Rust-Oleum primer can be used on
surfaces such as bare wood and treated wood.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT STRIKE
CAN. Contact Rust-Oleum. Shake often during use. Hold
can upright 10-12" from the surface and spray in a steady
back-and-forth motion, slightly overlapping each stroke.
Keep the can the same distance from the surface. Keep the
can in motion while spraying. Apply 2 or more light coats a
few minutes apart. Do not use near open flame.
DRY & RECOAT
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 20 minutes and is dry to handle in 1
hour. May be recoated in 1 hour or after 48 hours. The
finish coat is fully dry in 24 hours. NOTE: On plastic,
maximum paint adhesion and durability is achieved in 5-7
days. Chalked Clear Protective Topcoat can be applied for
added protection. Apply according to the label instructions.
DISTRESSING
This paint can be distressed if desired. To distress the
surface, lightly sand the surface with fine to medium grit
sandpaper or a sanding sponge. Wait 2 hours before
sanding or distressing.
CLEAN-UP
Wipe off tip before storing. Clean-up wet paint with xylene or
mineral spirits. Properly discard empty container. Do not
burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object into
can valve opening.