Manualshelf

Technical Specifications

ManualsBrandsRust-Oleum ManualsAll-Purpose Spray PaintPainter's Touch® Flat Black General Purpose Spray Paint - 11 oz.
12
TECHNICAL DATA
PTGP-05
PAINTER’S TOUCH
®
GENERAL PURPOSE
FLAT SPRAYS
1
DESCRIPTION AND USES
Rust-Oleum® Painter’s Touch® General Purpose Flat
Enamel Sprays are designed to provide long lasting
protection and durability. These sprays apply easily,
provide excellent coverage and dry fast to a tough attractive
finish. Painter’s Touch General Purpose Flat Enamel
Sprays feature an advanced spray system that allows you
to spray at any angle, even upside down for those hard to
reach areas. A comfort spray tip with a wider finger pad to
reduce fatigue caused by continuous spraying.
PRODUCTS
SKU (11 ounces)
DESCRIPTION
318513
Black
318516
White
COMPANION PRIMERS
SKU
DESCRIPTION
318622
White Primer
318623
Gray Primer
PRODUCT APPLICATION
PRIMING
Use of a Painter’s Touch® General Purpose Primer will
optimize adhesion and hiding and is recommended for bare
wood and metal.
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50°F (10°C) and
90ºF (32ºC) and humidity is below 65% to ensure proper
drying. Do not apply to surfaces, when heated, exceed
200°F (93°C). Do not apply to galvanized steel. Avoid
spraying in very windy and dusty conditions. Cover
surrounding area to protect from spray mist.
SURFACE PREPARATION
ALL SURFACES: Remove all dirt, grease, oil, salt and
chemical contaminants by washing the surface with Krud
Kutter
®
Original Cleaner Degreaser, commercial detergent
or other suitable cleaner. Rinse thoroughly with fresh water
and allow to fully dry. All surfaces must be dry at time of
application. Remove loose paint and rust with a wire brush
or sandpaper. Lightly sand glossy surfaces to create a
surface profile.
PRODUCT APPLICATION (cont.)
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT STRIKE
CAN. Contact Rust-Oleum. Shake often during use. Hold
can upright 10-16" from surface and spray in a steady back-
and-forth motion, slightly overlapping each stroke. Keep the
can the same distance from the surface. Keep the can in
motion while spraying. Apply two or more light coats a few
minutes apart to avoid drips and runs. Do not use near
open flame.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 20 minutes, to handle in 1 hour, and is fully dry in
24 hours. Apply a second coat or clear coat within 1 hour or
after 48 hours. Apply the clear coat in 2-3 light coats a few
minutes apart.
CLEAN-UP
Wipe off tip before storing. Clean-up wet paint with xylene
or mineral spirits. Properly discard empty container. Do not
burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not stick pin or other
objects into the stem.

Summary of content (2 pages)