Technical Specifications
TECHNICAL DATA RSD-60
ROCKSOLID
®
NATURAL LOOK CONCRETE SEALER
Form: GDH-1336
Rev.: 041817
1
.DESCRIPTION AND USES .
RockSolid
®
Natural Look Concrete Sealer seals and
protects concrete and masonry surfaces from the
damaging effects of water, chemicals and UV light. This
water-based film-forming formula provides a protective
barrier to keep water out, protect against stains and
extend the life of the concrete surface. The “natural look”
low gloss finish is suitable for use on driveways, patios,
walkways, pool decks, basements and more. This product
is not intended for use on garage floors.
Natural Look Concrete Sealer is suitable for use on interior
or exterior, stained or bare concrete and masonry
surfaces. Do not use on asphalt. Natural Look Concrete
Sealer is ideal for driveways, walkways, porches, patios,
pool decks and more. For ongoing maintenance, surfaces
previously sealed with RockSolid Natural Look Concrete
Sealer may be sealed again with this product (or another
water-base, film-forming sealer).
.PRODUCTS .
SKU Container Size
317928 1-Gallon Natural Look Concrete Sealer
PRODUCT FEATURES .
Seals and protects surface for chemicals & stains
Excellent water repellency
Long-lasting formula
PRODUCT APPLICATION .
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
SURFACE PREPARATION
Proper surface preparation is critical to achieve best
results. Allow newly poured concrete to cure for a
minimum of 28 days. Sweep away all loose dirt, debris
and remove any vegetation that could interfere with
application and performance. If necessary, use a wire
brush or sander to remove any loose or unsound concrete
or masonry. Remove any efflorescence with RockSolid
Efflorescence Remover (sold separately). Clean the entire
surface, including any oil or grease spots with RockSolid
Heavy Duty Cleaner (sold separately). Scrub with a stiff
bristle brush or broom. Rinse thoroughly with fresh water.
A power washer is preferred. Repeat as necessary to
completely clean and rinse. Allow to dry to the touch
(typically 4 to 6 hours) before applying RockSolid Natural
Look Concrete Sealer.
.PRODUCT APPLICATION (cont.) .
APPLICATION
RockSolid Natural Look Concrete Sealer is ready to use.
Do not thin. Use only when air (ambient) temperature is
between 50-90°F (10-32°C) and the relative humidity is
below 85% during the day and night. Do not apply in
direct sunlight. Do not apply if rain is expected within 24
hours. Use in a well ventilated area.
Mask adjacent surfaces to allow spray application up to all
edges. Protect delicate foliage from overspray. Apply
using a standard pump sprayer with an adjustable spray
tip.* Stir container to mix product. Fill pump sprayer with
product, then fully pressurize the sprayer. Set the spray tip
to a medium-fine mist and spray 10-12” from the surface.
Do not pour the product on the surface or allow product to
puddle.
Start and stop the sprayer just off the work area to prevent
drips. For larger areas, work in 6’x6’ sections at a time
before moving to the next section. Apply the product
evenly, using a circular or oval pattern to saturate the
surface. Backroll any puddles with a ⅜” to ½” nap roller.
For additional protection on heavy traffic areas or for more
porous surfaces, wait 4 to 6 hours to recoat. Occasional
touch-up or recoat may be necessary for areas subject to
heavy foot or vehicle traffic.
*An alternate method is to apply with a ⅜” or ½” nap roller
from a paint tray.
COVERAGE
Each gallon covers 200-400 square feet (single coat)
depending on the porosity of the surface. Porous surfaces
may require additional coats.
DRY TIME
Dry time is based on 70°F and 50% relative humidity.
Allow longer dry time at lower temperatures and higher
humidity. Wait a minimum of 4 to 6 hours for light foot
traffic. Wait 24-48 hours before returning heavy items,
furniture and vehicles. The surface will be fully cured in 72
hours.
CLEAN-UP
Wash tools and equipment with soap and water. Properly
dispose of all soiled rags and unused product.