Technical Specifications

TECHNICAL DATA RSD-59
ROCKSOLID
®
WET LOOK CONCRETE SEALER
Form: GDH-1335
Rev.: 041817
1
.DESCRIPTION AND USES .
RockSolid
®
Wet Look Concrete Sealer seals and protects
concrete and masonry surfaces from the damaging effects
of water, chemicals and UV light. This water-based film-
forming formula provides a protective barrier to keep water
out, protect against stains and extend the life of the
concrete surface. The “wet look” high gloss finish is
suitable for use on driveways, patios, walkways, pool
decks, basements and more. This product is not intended
for use on garage floors.
Wet Look Concrete Sealer is suitable for use on interior or
exterior, stained or bare concrete and masonry surfaces.
Do not use on asphalt. Wet Look Concrete Sealer is ideal
for driveways, walkways, porches, patios, pool decks and
more. For ongoing maintenance, surfaces previously
sealed with RockSolid Wet Look Concrete Sealer may be
sealed again with this product (or another water-base,
film-forming sealer).
.PRODUCTS .
SKU Container Size
317927 1-Gallon Wet Look Concrete Sealer
PRODUCT FEATURES .

Seals and protects surface from chemicals & stains

Excellent water repellency

Long-lasting formula
PRODUCT APPLICATION .
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
SURFACE PREPARATION
Proper surface preparation is critical to achieve best
results. Allow newly poured concrete to cure for a
minimum of 28 days. Sweep away all loose dirt, debris
and remove any vegetation that could interfere with
application and performance. If necessary, use a wire
brush or sander to remove any loose or unsound concrete
or masonry. Remove any efflorescence with RockSolid
Efflorescence Remover (sold separately). Clean the entire
surface, including any oil or grease spots with RockSolid
Heavy Duty Cleaner (sold separately). Scrub with a stiff
bristle brush or broom. Rinse thoroughly with fresh water.
A power washer is preferred. Repeat as necessary to
completely clean and rinse. Allow to dry to the touch
(typically 4 to 6 hours) before applying RockSolid Wet
Look Concrete Sealer.
.PRODUCT APPLICATION (cont.) .
APPLICATION
RockSolid Wet Look Concrete Sealer is ready to use. Do
not thin. Use only when air (ambient) temperature is
between 50-90°F (10-32°C) and the relative humidity is
below 85% during the day and night. Do not apply in
direct sunlight. Do not apply if rain is expected within 24
hours. Use in a well ventilated area.
Mask adjacent surfaces to allow spray application up to all
edges. Protect delicate foliage from overspray. Apply
using a standard pump sprayer with an adjustable spray
tip.* Stir container to mix product. Fill pump sprayer with
product, then fully pressurize the sprayer. Set the spray tip
to a medium-fine mist and spray 10-12” from the surface.
Do not pour the product on the surface or allow product to
puddle.
Start and stop the sprayer just off the work area to prevent
drips. For larger areas, work in 6’x6’ sections at a time
before moving to the next section. Apply the product
evenly, using a circular or oval pattern to saturate the
surface. Backroll any puddles with a ⅜” to ½” nap roller.
For additional protection on heavy traffic areas or for more
porous surfaces, wait 4 to 6 hours to recoat. Occasional
touch-up or recoat may be necessary for areas subject to
heavy foot or vehicle traffic.
*An alternate method is to apply with a ⅜” or ½” nap roller
from a paint tray.
COVERAGE
Each gallon covers 200-400 square feet (single coat)
depending on the porosity of the surface. Porous surfaces
may require additional coats.
DRY TIME
Dry time is based on 70°F and 50% relative humidity.
Allow longer dry time at lower temperatures and higher
humidity. Wait a minimum of 4 to 6 hours for light foot
traffic. Wait 24-48 hours before returning heavy items,
furniture and vehicles. The surface will be fully cured in 72
hours.
CLEAN-UP
Wash tools and equipment with soap and water. Properly
dispose of all soiled rags and unused product.