SDS

Date Printed: 9/19/2016
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Avoid runoff into sewers and waterways. Provide ventilation
and approach spill from upwind using proper personal protective equipment as indicated in Section 8. Carefully neutralize spill with
sodium bicarbonate (NaHCO3). Contain spilled liquid with sand or earth. DO NOT use combustible materials such as sawdust.
Dispose of according to local, state (provincial) and federal regulations. Do not incinerate closed containers.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.
Use only with adequate ventilation. Follow all MSDS/label precautions even after container is emptied because it may retain product
residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Store in a dry, well ventilated place. Keep container tightly closed when not in use.
8. Exposure Controls/Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
2-Propanol 67-63-0 55.0 200 ppm 400 ppm 400 ppm N.E.
Methyl Ethyl Ketone 78-93-3 15.0 200 ppm 300 ppm 200 ppm N.E.
Triethoxyoctylsilane 2943-75-1 10.0 N.E. N.E. N.E. N.E.
Sulfuric Acid 7664-93-9 5.0 0.2 mg/m3 N.E. 1 mg/m3 N.E.
Hydrochloric Acid 7647-01-0 1.0 N.E. N.E. N.E. 5 ppm
Methanol 67-56-1 1.0 200 ppm 250 ppm 200 ppm N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Provide general dilution of local exhaust ventilation in volume and pattern to keep TLV of
hazardous ingredients below acceptable limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Use impervious gloves to prevent skin contact and absorption of
this material through the skin. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
9. Physical and Chemical Properties
Appearance:
Liquid
Physical State:
Liquid
Odor:
Alcohol Like
Odor Threshold:
N.E.
Relative Density:
0.839
pH:
1.1
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Partially
Partition Coefficient, n-octanol/
water:
N.D.
Decompostion Temp., °C:
N.D.
Boiling Range, °C:
80 - 279
Explosive Limits, vol%:
2.0 - 12.0
Flammability:
Supports Combustion
Flash Point, °C:
-5
Evaporation Rate:
Slower than Ether
Auto-ignition Temp., °C:
N.D.
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid contact with strong acid and strong bases. Avoid contact with metals.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies. Product slowly corrodes copper,
aluminum, zinc, and galvanized surfaces.
HAZARDOUS DECOMPOSITION: Decomposition produces hydrogen chloride, chlorine and hydrogen gases.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
Page 3 / 5