How to Guide

ManualsBrandsRust-Oleum ManualsSpray Paint297069

TECHNICAL DATA INS-11

INSPIRE

FROSTED GLASS SPRAY

Form: GDH-1312

Rev.: 030117

.DESCRIPTION AND USES .

Rust-Oleum

Inspire Frosted Glass is a semi-transparent

finish that obscures vision, but permits light to shine

through painted objects. Ideal for use on glass doors,

windows, skylights, exterior shower doors and

greenhouses. For a decorative effect, use a stencil to

create an etched look on mirrors, shower doors, glass

accessories and more.

.PRODUCTS

SKU (11 ounces) DESCRIPTION

297069 Frosted Glass

PRODUCT APPLICATION .

READ ALL DIRECTIONS BEFORE BEGINNING

PROJECT

PAINTING CONDITIONS

Use outdoors or in a well ventilated area such as an open

garage. Use when temperature is between 50°F (10°C)

and 90ºF (32ºC) and humidity is below 85% to ensure

proper drying. Do not apply to surfaces, when heated,

exceed 200°F (93°C). Do not apply to galvanized steel.

Avoid spraying in very windy and dusty conditions. Cover

surrounding area to protect from spray mist.

SURFACE PREPARATION

Clean the surface with soap and water, rinse and let dry.

PRODUCT APPLICATION .

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Shake often during

use. Hold can upright 10-12" from surface and spray in a

steady back-and-forth motion, slightly overlapping each

stroke. Keep the can the same distance from the surface.

Keep the can in motion while spraying. Apply 2 or more

“wet” coats a few minutes apart for the best appearance.

(A “wet” coat should appear shiny as it is applied to the

surface). WAIT 10 MINUTES FOR THE FROST EFFECT.

Do not use near open flame.

DRY & RECOAT TIMES

Dry and recoat times are based on 70°F and 50% relative

humidity. Allow more time at cooler temperatures. May

recoat anytime. Dries completely in 5-10 minutes.

CLEAN-UP

When finished spraying, clear spray valve by turning the

can upside down and pushing the spray button for 5

seconds. Clean-up wet paint with xylene or mineral spirits.

Properly discard empty container. Do not burn or place in

home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not stick pin or other

objects into the stem.

NOTE: Frosted surfaces may be cleaned with a household

glass cleaner and soft cloth or hand washed with liquid

soap and water. Do not place items in a dishwasher. To

remove frosted finish from glass, use lacquer thinner or

acetone.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA INS-11 INSPIRE FROSTED GLASS SPRAY .DESCRIPTION AND USES PRODUCT APPLICATION . ® APPLICATION Rust-Oleum Inspire Frosted Glass is a semi-transparent finish that obscures vision, but permits light to shine through painted objects. Ideal for use on glass doors, windows, skylights, exterior shower doors and greenhouses. For a decorative effect, use a stencil to create an etched look on mirrors, shower doors, glass accessories and more.
PAGE 2
TECHNICAL DATA FROSTED GLASS SPRAY .PHYSICAL PROPERTIES . FROSTED GLASS SPRAY Resin Type Acrylic Polymer Pigment Type Amorphous Precipitated Silica Solvents Acetone, n-Butyl Acetate, Naphtha, Xylene MIR 1.35 Max Fill Weight 11 ounces Recommended Dry Film Thickness (DFT) per Coat 1.0-2.0 mils (25-50µ) Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity Recoat 8-12 sq.ft./can 2 (0.74-1.