How to Guide

ManualsBrandsRust-Oleum ManualsGarage Floor Paint293515

FLOOR COATING TECHNICAL DATA RSD-01

ROCKSOLID

POLYCURAMINE

GARAGE FLOOR COATING KIT

Form: GDH-604

Rev.: 082916

.DESCRIPTION AND USES .

RockSolid Floors

Polycuramine

Garage Floor Coating

Kit is designed to provide excellent hardness, adhesion

and durability on properly prepared concrete floors. It has

excellent resistance to salt, oil, gasoline and other harsh

chemicals. This garage floor coating contains zero VOC

making it environmentally safe and is packaged in

pouches, which reduces waste.

RockSolid Polycuramine is designed to be applied over

concrete surfaces. The surface should be free of loose

particles, rust, oils and contaminants. It is recommended

that this product be applied in 4’ X 4’ sections in an “M”

and “W” pattern to help ensure proper coverage.

. PRODUCT FEATURES .



Low odor and can be applied indoors



Formulated without the addition of VOC containing solvent



One coat system



45 minute pot life



Patented Burst Pouch Technology



96% solids formulation



Has excellent self-leveling properties



7 day recoat window without sanding



Excellent durability in a single coat

.KIT INCLUDES .



Polycuramine Burst Pouch



Foam Roller



Decorative Chips



Concrete Etch



Instructions

.PRODUCTS .

SKU Description

286879 Gray 2.5 Car Kit

286891 Gray 1 Car Kit

286890 Mocha 2.5 Car Kit

286892 Mocha 1 Car Kit

308637 Dark Gray 2.5 Car Kit

308638 Dark Gray 1 Car Kit

.PACKAGING .

Two part Burst Pouch Technology

(U.S. Patent Number 8,381,903 B2)

.APPEARANCE .

High gloss

PRODUCT APPLICATION .

SURFACE PREPARATION

Proper surface preparation is critical to achieve best

results. Scrub heavily soiled areas with RockSolid Heavy

Duty Degreaser or Rust-Oleum Cleaner & Degreaser (sold

separately). Scrub thoroughly, then rinse. Repeat as

needed.

.PRODUCT APPLICATION (cont.) .

SURFACE PREPARATION (cont.)

Use the supplied RockSolid concrete etch per the

instructions to provide the proper surface condition to

ensure proper adhesion. Rinse the floor thoroughly and

allow it to dry completely.

Moisture Testing - New concrete should be allowed to

cure for 30 days before application of any coating. If there

is any doubt about the dryness of the concrete, conduct a

test by simply taping a piece of 4 mil plastic sheet 18x18”

on the bare concrete for 24 hours. Be sure to tape all four

sides. After 24 hours, check the concrete for signs of

moisture. The concrete substrate will be darker if damp. If

moisture is found, allow additional drying time (10-14

days) and repeat the test.

Testing for Sealer - Check for curing compounds or other

types of sealers by pouring a small amount of water onto

the concrete. If water soaks in, the surface is suitable for

coating. If water beads up on the concrete, the surface is

not porous and a test application is warranted to ensure

proper adhesion will develop. Sanding or mechanical

abrading may be required if proper adhesion does not

develop.

Previously Coated Floors - Previously coated floors

need to be in good condition with proper adhesion to the

concrete substrate. Check the adhesion of the previous

coating by cutting a small X in the coating using a sharp

razor knife. Firmly apply a piece of 5” duct tape over the

center of the X cut, and then pull off with a fast snap. If

more than 10% of the taped area is removed, the original

coating is not bonded well and needs to be removed

chemically or mechanically with a grinder.

WARNING! If you scrape, sand or remove old paint from

any surface, you may release lead paint dust. LEAD IS

TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE

SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;

ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH

approved respirator to control lead exposure. Clean up

carefully with a HEPA vacuum and a wet mop. Before you

start, find out how to protect yourself and your family by

contacting the National Lead Information Hotline at 1-800-

424-LEAD or log on to www.epa.gov/lead.

MIXING

MIX ONLY ONE POUCH AT A TIME. Both components

and the environment should be pre- conditioned to a

minimum of 40ºF (4ºC) prior to use. Be sure the air and

surface temperatures are at least 5º above the dew point.

Summary of content (3 pages)

PAGE 1
FLOOR COATING TECHNICAL DATA RSD-01 ROCKSOLID® POLYCURAMINE® GARAGE FLOOR COATING KIT .DESCRIPTION AND USES ® . .PRODUCT APPLICATION (cont.) ® RockSolid Floors Polycuramine Garage Floor Coating Kit is designed to provide excellent hardness, adhesion and durability on properly prepared concrete floors. It has excellent resistance to salt, oil, gasoline and other harsh chemicals. This garage floor coating contains zero VOC making it environmentally safe and is packaged in pouches, which reduces waste.
PAGE 2
TECHNICAL DATA ROCKSOLID® POLYCURAMINE® GARAGE FLOOR COATING KIT .PRODUCT APPLICATION (cont.) . .PRODUCT APPLICATION (cont.) . MIXING (cont.) CLEAN-UP Combine the two components by placing the pouch on the ground and rolling it from the part A side towards the part B side like a tube of toothpaste. This will create pressure in the part A side and force the middle seal to burst, allowing the two components to mix together.
PAGE 3
TECHNICAL DATA ROCKSOLID® POLYCURAMINE® GARAGE FLOOR COATING KIT .PHYSICAL PROPERTIES . Resin Type Proprietary Blend of Epoxy, Urethane and Polyurea Pigment Varies with color Solvent Benzyl Alcohol, 1-Choro-4-(Trifluoromethyl) Benzene, Nonylphenol, Neopentyl Glycol Diglycidyl Ether Weight Per Gallon 9.1-9.3 lbs. Per Liter 1.09-1.11 kg Solids By Volume 96% Volatile Organic Compounds <1 g/l 200-250 sq.ft./kit (4.9-6.