Technical Specifications
TECHNICAL DATA RSD-13
ROCKSOLID
®
PAVER LOCK
Form: GDH-906
Rev.: 043018
1
.DESCRIPTION AND USES .
RockSolid
®
Paver Lock is specially formulated to lock the
joint sand between pavers to create a longer lasting look.
Paver Lock penetrates below the surface while enhancing
the natural appearance of the paver. Application is quick
and easy using a standard garden sprayer or paint roller.
Paver Lock can be used with any color paver and is
suitable for use on driveways, walkways, stairs, patios,
pool decks, retaining walls and more. Paver Lock is safe
to use near grass and plants.
.PRODUCTS .
SKU Container Size
293411 1-Gallon Paver Lock
293439 5-Gallon Paver Lock
. PRODUCT FEATURES .
Excellent paver sealer and joint sand stabilizer
Excellent water repellency
Penetrating formula enhances natural appearance of
pavers
PRODUCT APPLICATION .
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
SURFACE PREPARATION
Proper surface preparation is critical to achieve best
results. Sweep away all loose dirt and debris and remove
any vegetation that could interfere with application and
performance. Remove any efflorescence with RockSolid
Efflorescence Remover (sold separately). Clean the entire
surface, including any oil or grease spots with RockSolid
Heavy Duty Cleaner (sold separately). Scrub pavers with a
stiff bristle brush or broom. Rinse thoroughly with fresh
water. A power washer is preferred. Repeat as necessary
to completely clean and rinse. Allow to thoroughly dry.
.PRODUCT APPLICATION (cont.) .
APPLICATION
RockSolid Paver Lock is ready to use. Do not thin. Use
only when air (ambient) temperature is between 50-90°F
(10-32°C) and the relative humidity is below 85% during
the day and night. Do not apply in direct sunlight. Do
not apply if rain is expected within 24 hours. Pavers and
locking sand must be dry for proper penetration of the
sealer.
Mask adjacent surfaces to allow spray application up to all
edges. Protect delicate foliage from overspray. Stir or
shake the container to mix the sealer. Apply using a
standard garden sprayer with an adjustable spray tip. An
alternate method is to apply with a ⅜” or ½” nap roller from
a paint tray. Do not pour the sealer directly on the surface.
Fill the pump sprayer with sealer, then fully pressurize the
sprayer. Set sprayer tip to a medium-fine mist and spray
10-12” from the surface.
Start and stop the sprayer just off the work area to prevent
drips. For larger areas, work in 6’x6’ sections at a time
before moving to the next section. Product will appear
milky white, but dries clear. Apply sealer evenly, using a
circular or oval pattern. Apply a saturating coat so pavers
and joints remain wet for several minutes before sealer is
absorbed. Wait 5-10 minutes, then back roll with a ⅜” to ½”
nap roller to prevent puddles and soften overlap marks. A
second coat is recommended for more porous pavers.
Follow the same application method and back roll.
COVERAGE
Each gallon covers up to 150 square feet (single coat).
The actual coverage will vary depending on the porosity of
the surface. Porous pavers will require multiple coats.
DRY TIME
Dry time is based on 70°F and 50% relative humidity.
Allow longer dry time at lower temperatures and higher
humidity. Paver Lock will dry to the touch in 1 hour. Allow
a minimum of 2 hours for foot traffic. Wait overnight before
returning heavy items, furniture and vehicles. The surface
will be fully cured in 72 hours.
CLEAN-UP
Wash tools and equipment with soap and warm water.
Clean spills with mineral spirits. Properly dispose of all
soiled rags and protect unused product from freezing.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO
NOT TAKE INTERNALLY.