How to Guide
TECHNICAL DATA RST-10
RESTORE
®
10X ADVANCED RESURFACER
STAIN
Form: GDH-686
Rev.: 042115
1
DESCRIPTION AND USES .
Restore
®
10X Advanced Resurfacer is a high build, water
based acrylic coating designed to resurface aged wood and
concrete decks, patios, and walkways. The high build textured
finish provide slip resistance and can bridge over or fill ¼” cracks,
checks, nail holes, or other minor surface defects.
FOR DECKS: For wood and most composite decks.
Follow specific manufacturer’s recommendation before
applying to any composite decking.
FOR CONCRETE: For use on broom swept or porous
concrete surfaces. Do not use on smooth or floated
concrete, fiberglass, tile or metal surfaces. Not
recommended for driveways, garages or other areas with
vehicular traffic.
FOR EXTERIOR USE ONLY AND NOT RECOMMENDED
FOR DRIVEWAYS, GARAGES OR OTHER AREAS WITH
VEHICULAR TRAFFIC.
Restore 10X Advance Resurfacer must be tinted before use.
The use of the Restore Honeycomb Roller is required for
proper application. (one roller for every 8 gallons).
. FEATURES .
Excellent weather resistance
Fills ¼” cracks
Excellent water repellency
Ready for use in 48 hours
.PRODUCTS .
SKU Description
287327 10X Advanced Tint Base - 4-Gallon
287328 10X Advanced Tint Base - 1-Gallon
287329 10X Advanced Tint Base - 3-Gallon
287844 10X Advanced Navajo Red - 1-Gallon
287843 10X Advanced Beach – 1-Gallon
287840 10X Advanced Cape Cod Gray – 1-Gallon
287807 10X Advanced Timberline – 1-Gallon
287908 10X Advanced Navajo Red – 4-Gallon
287905 10X Advanced Beach – 4-Gallon
287903 10X Advanced Cape Cod Gray – 4-Gallon
287902 10X Advanced Timberline – 4-Gallon
COMPANION PRODUCTS ...
SKU Description
51752 Restore Deck & Concrete Cleaner
51750 Restore Crack Filler
287517 Restore Deck Start Wood Primer – 1-Gallon
287518 Restore Deck Start Wood Primer – 5-Gallon
287523 Restore 2X One Coat Solid Stain
287912 Restore Deck Stripper
20114 Honeycomb Roller Cover 4 inch
RRC-0-2009 Honeycomb Roller Cover 9 inch
41100 Restore 4X Deck Coat – 1-Gallon
47000 Restore Solid Acrylic Stain
PRODUCT APPLICATION .
REGARDLESS OF AGE OR SURFACE CONDITION,
FAILURE TO FOLLOW ONE OF THESE PREPARATION
METHODS WILL RESULT IN POOR ADHESION AND
POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD
DECKS NEED TO WEATHER AT LEAST 6 MONTHS
BEFORE APPLICATION.
SURFACE PREPARATION
NEW WOOD
New wood may be wet with chemicals or have mill glaze from
the manufacturing process. New wood should age for a
minimum of 6 months before applying Restore 10X Advanced
Resurfacer. The lumber must be dry completely before applying
the product to prevent peeling of the coating. The surface must
also be properly cleaned and prepared using Restore Deck &
Concrete Cleaner to remove all foreign material and mill glaze
prior to application. Follow the PREPARATION instructions to
ensure the Restore 10X Advanced Resurfacer adheres properly
to the wood.
READ ALL INSTRUCTIONS BEFORE BEGINNING
PROJECT.
PREPARATION WITH RESTORE DECK START WOOD
PRIMER (HIGHLY RECOMMENDED)
Clean the surface using a deck brush and Restore Deck &
Concrete Cleaner. The surface must be clean and free of dirt,
grease, mildew and organic growth. For best results, use a
pressure washer, in addition to the Restore Deck & Concrete
Cleaner, to remove embedded dirt and grime. (Use at a low
pressure setting of 500-1200 psi. Do not use high pressure as it
may harm the wood). Loose paint needs to be scraped. For light
repairs, secure raised nails heads, deck screws or loose deck
boards. Remove loose splinters and replace severely damaged
or rotting boards. Fill cracks, more than ¼” with Restore Crack
Filler or similar acrylic, non-silicone filler. Allow to dry. Apply
Restore Deck Start Wood Primer using a ⅜” nap roller. Saturate
the roller cover and apply generously in a consistent pattern.
Work to a wet edge at all times.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and a wet
mop. Before you start, find out how to protect yourself and your
family by contacting the National Lead Information Hotline at
1-800-424-LEAD or log on to www.epa.gov/lead.
PREPARATION WITH RESTORE DECK STRIPPER
Previously applied coatings and existing stain/sealers need to be
removed completely. Strip the surface using a deck brush and
Restore Deck Stripper. Then sand the surface using 50 or 60 grit
sandpaper. Follow by cleaning the surface using a deck brush
and Restore Deck & Concrete Cleaner. The surface must be
clean and free of dirt, grease, mildew and organic growth. Allow
to dry.