Technical Specifications

ManualsBrandsRust-Oleum ManualsSpray Paint267689

TECHNICAL DATA SPC-31

GLITTER SPRAYS

.DESCRIPTION AND USES .

Glitter Sprays are designed to provide a sparkle finish on

many surfaces including wood, metal, wicker, ceramic,

pottery, Styrofoam

®,

paper, plastic, and more. For added

protection, top coat with Rust-Oleum

Glitter Sealer. The

clear topcoat helps prevent Glitter from flaking and fading

while maintaining the sparkle finish. For use on interior

items only.

.PAINTING CONDITIONS .

Use outdoors or in a well ventilated area such as an open

garage. Use when temperature is between 50ºF (10ºC)

and 90ºF (32ºC) and humidity is below 65% to ensure

proper drying. Do not apply to surfaces that, when heated,

exceed 200°F (93°C). Avoid spraying in very windy and

dusty conditions. Cover surrounding area to protect from

spray mist.

.PRODUCT APPLICATION .

SURFACE

PREPARATION

Remove all dirt, grease, oil, salt and chemical contaminants

washing the surface with a commercial detergent, or

other

suitable cleaning method.

Rins

e with fresh water and allow to

thoroughly dry. Remove loose paint and rust with a wire brush

or sandpaper. Lightly sand glossy surfaces to create

surface profile.

ARNING! If you

scr

ape, sand or remove

old

paint from any surface, you may release lead paint

dust.

LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE

SERIOUS ILLNESS, SUCH AS BRAIN

DAMAGE;

ESPECIALLY IN CHILDREN. PREGNANT

OMEN

SHOULD ALSO AVOID EXPOSURE.

ear a

NIOSH

approved respirator to control lead exposure. Clean

carefully with a HEPA vacuum and a wet mop. Before

you

start, find out how to protect yourself and your family

contacting the National Lead Information Hotline at

1-800-

424-LEAD or log on to www.epa.gov/lead.

APPLICATION

Shake can vigorously for one minute after the mixing

ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE

CAN. Contact Rust-Oleum. Shake often during use. Hold

can

upright 12-14” from surface and spray in a steady

back-and-

forth motion, slightly overlapping each stroke. Keep the

the same distance from the surface. Keep the can in

motion

while spraying. Apply two or more light coats a few

minutes

apart. Do not use near open

flame.

DRY &

RECOAT

Dry and recoat times are based on 70ºF and 50%

relative

humidity. Allow

mor

e time at cooler temperatures. Dries

touch in 20 minutes, to handle in 1 hour, and fully dry in

hours. Recoat at

anytime.

CLEAN-UP

When finished spraying, clear valve by turning can upside

down and pushing spray button for 5 seconds. Clean-up wet

paint with xylene or miner al spirits.

operly discard

empty

container. Do not burn or place in home trash compactor.

CLOGGING

If the valve

logs, twist and pull off spray tip and rinse in

solvent such as mineral spirits. Do not insert any object into

can valve opening.

* Styrofoam

is a trademark of the Dow Chemical Company.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA SPC-31 GLITTER SPRAYS .DESCRIPTION AND USES . .PRODUCT APPLICATION SURFACE PREPARATION Glitter Sprays are designed to provide a sparkle finish on many surfaces including wood, metal, wicker, ceramic, ®, pottery, Styrofoam paper, plastic, and more. For added ® protection, top coat with Rust-Oleum Glitter Sealer. The clear topcoat helps prevent Glitter from flaking and fading while maintaining the sparkle finish. For use on interior items only.
PAGE 2
TECHNICAL DATA GLITTER SPRAYS .PHYSICAL PROPERTIES . Physical Properties Finishes Resin Type Acrylic Pigment Type Glitter Flake MIR 1.20 Max Fill Weight 10.25 ounces Solvents Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 77º F (25º C) and 50% Relative Humidity Touch Naphtha, Hexane 3-5 sq.ft./can (Colors) 6-10 sq.ft.