Technical Specifications
TECHNICAL DATA
SPC-08
SPECIA
LTY
FROSTED GLASS
SPR
A
YS
DESCRIPTION AND USES
R
u
s
t
-
O
l
e
u
m
®
Frosted Glass Spray creates an etched
g
l
ass
appearance but permits light to transmit through the p
a
i
n
t
e
d
surface. It is designed for use on glass doors,
windows,
skylights, shower doors, and greenhouses. For a
d
e
c
o
r
a
t
i
ve
effect, use a stencil to create an etched look on mirrors,
s
h
o
w
e
r
door exteriors, glass accessories, and
m
o
r
e
.
PRODUCT
APPLICA
TION
PAINTING
C
O
N
D
I
T
I
O
NS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50°F (10°C) a
nd
90°F (32°C) and humidity is below 65% to ensure p
r
o
p
e
r
drying.
Do not apply to surfaces, when heated, exceed
200
°
F
(93°C). or surfaces that are exposed to repeated or
c
o
n
t
i
nu
o
u
s
water contact, such as the inside of shower doors.
A
vo
i
d
spraying in very windy and dusty conditions. Cover s
u
rr
o
und
i
ng
area to protect from spray
m
i
s
t
.
SURFACE
P
R
E
P
A
R
AT
I
O
N
Remove all dirt, grease, oil, salt and chemical
c
o
n
t
a
m
i
n
a
n
t
s
by washing the surface with a commercial detergent, or other
suitable cleaning method. Rinse with fresh water and allow
t
o
thoroughly d
r
y
.
PRODUCT APPLICATION
(cont.)
A
PP
L
I
C
AT
I
O
N
Shake can vigorously for one minute after the mixing ball b
e
g
i
n
s
to rattle. If mixing ball fails to rattle
DO NOT STRIKE CAN.
C
o
n
t
a
c
t
R
u
s
t
-
O
l
e
u
m.
Shake often during use. Hold can upright
10-16”
from surface and spray in a steady
back-and-forth motion, slightly
overlapping each stroke. Keep the can in motion while s
p
r
ay
i
ng
.
Apply two or more wet coats a few minutes apart for b
es
t
appearance. A wet coat should appear shiny as
it
is applied to
t
h
e
surface. WAIT
10 MINUTES FOR FROST EFFECT.
Not for
o
u
t
d
oo
r
use.
Do not use near open
flam
e
.
DRY & RECOAT T
I
M
E
S
Dry and recoat times are based on 70°F and 50%
r
e
l
a
t
i
ve
humidity. Allow more time at cooler temperatures.
D
r
i
es
completely in 5-10 minutes. May recoat
a
n
y
t
i
m
e
.
C
L
E
A
N
-
U
P
When finished spraying, clear spray valve by turning can up
s
i
d
e
down and depressing spray button for
3-5
seconds (some
p
a
i
n
t
will be sprayed out, so be careful to not inadvertently
s
p
r
ay
yourself or other objects).
C
l
ea
n
-
up
wet paint with xylene
o
r
mineral spirits. Properly discard empty container. Do not burn
o
r
place in home trash
c
o
m
p
a
c
t
o
r
.
C
L
OGG
I
N
G
If the valve clogs, twist and pull off spray tip and rinse in a
so
l
ve
n
t
such as mineral spirits. Do not insert any object into can valve
op
e
n
i
ng
.
1
Form: 5016790
Rev.: 080811