Technical Specifications
TECHNICAL DATA
MAC-01
METALLIC ACCENTS
DESCRIPTION AND USE
R
u
s
t
-
O
l
e
u
m
®
Metallic Accents is a
water-based c
oa
t
i
ng
that provides a metallic finish for walls, ceilings, doors,
a
nd
furniture. This one step finish contains mica beads to provide a
metallic appearance and is low
o
d
o
r
.
PRODUCT APPLICATION
(cont.)
PAINTING
C
O
N
D
I
T
I
O
NS
Use when temperature is between 50°F (10°C) and
85
°
F
(32°C) and humidity is below 85% to ensure proper d
r
y
i
ng
.
SURFACE
P
R
E
P
A
R
AT
I
O
N
Remove all dirt, grease, oil, salt and chemical
c
o
n
t
a
m
i
n
a
n
t
s
by washing the surface with a commercial detergent, or
o
t
h
e
r
suitable cleaning method. Rinse with fresh water and allow
t
o
thoroughly dry. Remove loose paint and rust with
a wire brush
or sandpaper. Lightly sand glossy surfaces. LEAD IS T
OX
I
C
.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS,
S
UC
H
AS BRAIN DAMAGE; ESPECIALLY IN CHILDREN. PR
EG
N
A
N
T
WOMEN SHOULD ALSO AVOID
E
XPO
S
UR
E
.
PRODUCT APPLICATION
(cont.)
Wear a NIOSH
approved respirator to control lead exposure.
C
l
ea
n
up carefully with a
HEPA
vacuum and a wet mop. Before you s
t
a
r
t
,
find out how to protect yourself and your family by contacting
t
h
e
National Lead Information Hotline at
1
-
800
-
424
-
L
E
A
D
or log on
t
o
www
.
e
p
a
.
g
ov
/
l
ea
d
.
PRIMING
Use of a latex primer
(
A
m
e
r
i
c
a
n
®
A
cc
e
n
t
s
®
7980 White
P
r
i
m
e
r
)
promotes adhesion and enhances hiding and is
es
p
e
c
i
a
ll
y
recommended for bare wood and bare metal, new drywall or
ove
r
contrasting
c
o
l
o
r
s
.
A
PP
L
I
C
AT
I
O
N
Before using, stir thoroughly to ensure any settled pigment is
r
e
-
dispersed. A
¼"
nap roller is recommended for large surface
a
r
eas
such as a wall. Start in an appropriate 4 foot area and apply in a
straight up and down motion, ceiling to floor (versus a
‘
W
’
m
o
t
i
o
n
)
.
End the stroke on the downward roll. Move to the next a
d
j
a
c
e
n
t
area and repeat the technique, slightly overlapping the just
a
pp
li
e
d
wet area (about 2 inches). Use a small width
¼"
nap roller
f
o
r
cutting in corners, ceilings, and baseboards.
NOTE: The
paint
fi
n
i
s
h
will have a subtle texture. If applying by brush, use a high qu
a
li
t
y
brush recommended
for water-based semi-gloss paints.
For
s
p
r
ay
application follow equipment
m
a
nu
f
a
c
t
u
r
e
r
’
s
directions
c
a
r
e
f
u
ll
y
.
Always keep the spray gun ten to twelve inches from the surface
and in motion while
s
p
r
ay
i
ng
.
DRY & RECOAT T
I
M
E
S
Dry and recoat times are based on 77°F (25°C) and 50%
r
e
l
a
t
i
ve
humidity. Allow more time at cooler temperatures. A minimum
o
f
two coats are recommended. Dries to touch in 30 minutes, d
r
i
es
to handle in 2 hours, and is fully dry in 24 hours. The finish
m
ay
be recoated in 30 minutes. Clear Coat: For outdoor or high
w
ea
r
interior surfaces such as furniture, a topcoat of
R
u
s
t
-
O
l
e
u
m
®
253613 Satin Clear may be applied after 24
h
o
u
r
s
.
C
L
E
A
N
-
U
P
Clean brush and other application tools immediately with soap a
nd
w
a
t
e
r
.
1
Form: 5107790
Rev.: 091411