Technical Specifications

ManualsBrandsRust-Oleum ManualsConcrete, Basement & Garage Floor Paint1 gal. Armor Gray Satin Concrete Floor Paint (2 Pack)

Form: CS1077

Rev.: 061812

TECHNICAL DATA

ESH-10

EPOXYSHIELD

1-PART CONCRETE

PAINT

DESCRIPTION AND USES

EPO

XYShield

Water-based One Part Concrete Paint

is modified

acrylic floor paint designed for use on carports, garages,

driveways, basements, porches, patios, walkways, and pool

decks. It may also be used on indoor or outdoor

vertical

masonry or concrete surfaces. It is not intended for use on

unsound previous coatings or floors that have a

moisture

problem.

APPEARANCE

Dries to a satin finish. Solid base color with

a color fleck finish.

Available in standard Armor Gray or Battleship Gray and a

tint

base that can be tinted to 14 colors. Decorative vinyl chips

various color combinations can be purchased separately to be

used with this

coa

ting.

PRODUCT

APPLICA

TION

SURFACE

PREP

ARA

TION

Allow new concrete to cure for a minimum of 28 days. Sweep

away all loose dirt and debris. Remove any

oil spots, grease or

spills and wash the floor with a suitable detergent or degreasing

solution and

rinse.

Then etch the floor using the Rust-Oleum

Concrete Etch.

PREVIOUSLY COATED FLOORS:

Make sure the floor is clean and

dry. Use a wire brush to remove any loose

or peeling paint or stain.

If floor is sealed, the sealer will have to be removed by

grinding

or shot

blasting.

To ensure proper adhesion, scuff

sand the entire

surface.

WARNING! If you scrape, sand or remove old

paint,

you may release lead dust. LEAD IS TOXIC. EXPOSURE TO

LEAD

DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE,

ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO

AVOID EXPOSURE.

Wear a NIOSH-approved respirator to

control

lead exposure. Clean up carefully with

a HEPA vacuum and a

wet

mop. Before you start, find out how to protect yourself and your

family by contacting the National Lead Information Hotline

1-800-424-LEAD or log on to

www

.epa.gov/lead.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA ® ESH-10 EPOXYSHIELD® 1-PART CONCRETE PAINT DESCRIPTION AND USES PRODUCT APPLICATION EPOXYShield® Water-based One Part Concrete Paint is modified acrylic floor paint designed for use on carports, garages, driveways, basements, porches, patios, walkways, and pool decks. It may also be used on indoor or outdoor vertical masonry or concrete surfaces. It is not intended for use on unsound previous coatings or floors that have a moisture problem.
PAGE 2
TECHNICAL DATA ® EPOXYSHIELD® 1-PART CONCRETE PAINT PRODUCT APPLICATION (cont.) MIXING Mix thoroughly to re-disperse to ensure any settled pigment is re-dispersed. Do not mix the color chips in with the coating. APPLICATION Apply only when air, material, and surface temperatures are between 60-85°F (15-29°C) and the surface temperature is at least 5°F (3°C) above the dew point. The relative humidity should not be greater than 85%. Stir thoroughly.
PAGE 3
TECHNICAL DATA ® EPOXYSHIELD® 1-PART CONCRETE PAINT PHYSICAL PROPERTIES 1-PART CONCRETE PAINT Resin Type Modified Acrylic Copolymer Pigment Type Varies with color Solvents Weight* Solids* Dipropylene Glycol Monobutyl Ether, Water Per Gallon 10.30-10.70 lbs. Per Liter 1.23-1.28 kg By Weight 46.8-50.4% By Volume 34.1-35.7% Volatile Organic Compounds* <250g/l (2.08 lbs./gal.) Mixing Ratio None Recommended Dry Film Thickness (DFT) Per Coat 3.0-3.5 mils (75-87.